Locking Glass Door

Sliding Door Safety Locks | Safety Door Locks

If the sliding glass doors in your home are more than 10 years old, you might notice that they are becoming harder to slide open. This problem is even more common on aluminum frame dual pane doors. The reason is because the doors are heavier due to the dual pane glass, but many of the aluminum units did not use stainless steel rollers. So, in many cases, the rollers get rusty from moisture and they start to bind.

In order to replace the rollers, you have to remove the sliding panel from the opening. In most instances, the fixed panel must be removed in order for the sliding panel to come out. There is a simple way to determine whether or not your fixed panel has to come out as well. If the slider is on the inside track and the fixed panel is on the outside track, you have to remove both panels, because the slider will only come out from the outside. There is a lip on the bottom of the track inside your house. That lip keeps water from coming in. Unfortunately, that lip is also too high to lift the sliding panel up and over. So, you have to remove the fixed panel first, then lift and swing out the slider from outside. If you are one of the few people who have a slider on the outside track, then you can lift your slider out without removing the fixed panel.

But, let's assume you need to remove the fixed panel first. Here is what you do: Remove your screen door if you have one. The screen door will have two rollers on the bottom. Lift one end of the door frame with one hand while using a flat screwdriver to lift the roller off the track. Do that on both sides, then take out the screen door and set it aside. Now, look for a metal piece on the bottom track that runs from the bottom corner of the fixed panel all the way across to the bottom of the side jamb that has the door lock hardware. If your door is really old that piece might be missing. If you have one, you can pry it up from the track. It is snapped in place even though it looks like it is a part of the track. Once you have that piece removed, you want to look inside the house where the fixed panel is against the wall jam. Look for screws holding the frame to the jam. They usually have one near the top and bottom corners, and one near the center. Remove these screws and put them where you won't lose them. Now, you should be able to pull the fixed panel out of the side jam. There is a very good chance that it will be stuck. If it is, grab the center rail near the bottom and lift up as hard as you can. If you feel the panel go up, pull it back down. Do this a couple of times, then try to pull it out of the side jam again. This usually loosens it enough to pull it out. If it still won't come out, you will have to put a thin screwdriver between the fixed panel frame and the side jam and pry while a helper pulls the panel away from the jam. Once you get it free of the side jam, grab the fixed panel side rail and have a helper grab the other rail. Lift the panel up into the top track and swing the bottom out of the bottom track. Remove the panel from the top track and set it aside with the screen door.

Now, you can try lifting the slider up and out, just like you did with the fixed panel. If the slider won't clear the bottom track, you need to do a couple of things. First, look to see if it's the old rollers protruding from the bottom that is preventing the door from coming out, or if the actual bottom of the door frame is hitting the track. In almost all cases, it will be the old rollers. But, if the opening is 8' wide, sometimes the wood header that runs across the opening has sagged just enough to make it tight in the center of the opening. If it's the rollers, you need to adjust them all the way up into the door. Look for a hole on the bottom side where you can put a phillips screwdriver and find the adjustment screw. Then turn that screw counterclockwise as far as you can. Do that to both sides, then try lifting out the door. If you are still getting stuck, have your helper lift one side and pull outward while you try to pry the frame and roller over the track. If you get one side out, have your helper hold that side with his or her foot to prevent it from going back in while he or she lifts the other side for you to pry free.

Once you get the slider out, almost all rollers are held in place by the same screw that holds the frame corners together. So, you need to set the panel on one side, remove the screw in the corner, flip the panel over, remove the screw on the other bottom corner. Now, you can take a rubber mallet or the wood handle of a hammer, and tap the bottom frame off the glass. This will give you access to your rollers. Take a close look at how they are inserted into the door frame. In fact, it's a good idea to only remove one roller to bring with you to match for the new ones. Then, when you get back home, you can use the roller that is still in place as a guide to installing the new ones.

Places like Home Depot, Lowes, and Ace Hardware carry about 80-90% of the rollers out there. So, you should be able to find them. However, let's say this just isn't your lucky day, and you can't find your rollers anywhere. You are going to have to have them ordered. Bring the roller to your local glass shop. If you're lucky, they will have them in stock. If not, they can order the rollers, but you won't get them for about a week. Don't panic. Just go home and tap the bottom frame back on the door panel, but leave the corner screws out. You can even leave the roller out that you removed. Lift the door back in place, install the fixed panel but don't snap the bottom piece back in, and don't install the inside screws. Then, from inside the house, lift the slider and pull it closed. You don't want to drag it if you left the roller out. It will scrape the bottom track. Just lift it enough to take the pressure off, and close and lock it.

About the Author

http://www.safetydoorlocks.blogspot.com/2010/09/sliding-door-safety-locks_20.html

Staywell 4-Way Locking Pet Door with Tunnel - White. $16.99 Easy to install and set up, this cat flap is activated by a magnetic collar key which is worn by your cat. The key allows your feline friend to come and go as it pleases, without the worry of stray cats entering your home. Suitable for medium sized cats up to 7kgs, the locking door can be fitted into windows, walls and thin panel doors.White plastic.Suitable for medium sized cats up to 7kgs/15lbs.Endorsed by Staywell/PetSafe.Operated by magnetic collar key with 1 included.4-way lock: in/out/opened/locked.Manual locking system.Max weight of pet the flap is suitable for: 7kg.Max shoulder width 16.2cm.Suitable for: glass, wood and most types of PVC doors.Suitable for thickness of 5.1cm.Can be fitted into walls and also can be fitted into windows.Assembly required.Weather resistant.Instructions included.When children are present in the home, it is important to consider the pet door during child proofing activities, the pet door may be misused by a child resulting in the child accessing potential hazards that may be on the other side of the pet door. Purchasers/Homeowners with swimming pools should ensure that the pet door is monitored at all times and that the swimming pool has adequate barriers.Overall size H22.4, W22.4, D9.5cm.Door size H16.9, W16.9cm.Manufacturer's 3 year guarantee.EAN/MPN/UPC/ISBN: 5011569005851

300 Stained Glass Cabinet Door Designs Pattern Cd $9 Update Your Kitchen Cabinets 300 Designs on One CD. From the best selling book 300 Stained Glass Cabinet Door Designs (item 6078) comes this convenient pattern CD. The CD features all 300 designs found in the original book as line art. Includes both full-size scans and thumbnails in Tiff format for easy downloading and printing. This CD literally offers hundreds of designs to help you create the absolute most beautiful cabinet doors for your home. Over 300 line designs, choose from prairie, Victorian, contemporary, scenic, nature and bevel themes.

300 Stained Glass Cabinet Door Designs $18.95 Update Your Kitchen with New Cabinet Doors. This best selling book literally has hundreds of designs to choose from to create the absolutely most perfect cabinet doors for you and your home. Over 300 line designs and 50 color pictures of finished cabinets will stir your imagination and get you started on that kitchen overhaul. Choose from prairie, Victorian, contemporary, scenic, nature and bevel themes.

Gs 11-9 With 4 Bead Door $794.95 Flip Bead Door Makes this the Perfect Kiln for Lampworkers and Fusers Alike. This kiln comes with a fiber bead door that flips open, making it easy to put in your glass beads for annealing. The easy-to-use kiln controller lets you customize and store up to 22 custom programs. Includes kiln shelf, posts, kiln wash and fire brick stand. Operates on 120v. Firing chamber 11 x 9deep, with a 4 fiber bead door for easy access. 2 year warranty, manufactured by Jen-Ken. 70 lbs. Ships via UPS. Features Easy to use 3-button digital controller with 4 programs (8 segments each) Bead door for fast and easy access 120v current, no special wiring needed

Prime Line Products Sliding Glass Door Pull With Locking Unit C1041 $33.49 Includes 1 Black painted die cast pull 1 keyed locking unit with 2 keys and 2 No. 832 x 2 Phillips flat head machine screws

Door Bevel Cluster $219 This gorgeous bevel cluster is perfect for large projects like windows, doors, or sidelights. Assembled bevel measures 13-7/8 wide by x 42 tall. 75 pieces. Delphi Tip Always lay out bevel clusters on pattern before cutting glass to adjust for small differences.

Man Locking Door, Close-Up $24.99 Man Locking Door, Close-Up - Photographic Print

Locking Fuel Door by Rampage $77.99 2007-11 JK Wrangler, Rubicon and Unlimited;Black powder coat;Seals gas tank to OE Specifications;Locking fuel door

Uroboros Garden Variety Glass Pack $144.95 A $261 Value - Save $121. Contains 25 pieces each 6 x 12 (12 1/2 sq. feet) of the finest Tiffany reproduction glass available. You get 8 pieces of flower glass (3-4 different colors), 8 pieces of leaf glass (3-4 different colors), and 9 pieces of background glass (2 different colors). Perfect for floral lamp shades or Tiffany-style windows. Sold only as a package, regular retail price is 50% below comparable Uroboros individual sheets. UPS ships this factory pack right to your door. There are no extra boxing charges for glass packs. Photo is one example. Actual glass may vary from photo. Project from Innovative Stained Glass Panels book 6991.

Delphi Ez-pro 11-4.5 Kiln With Flip Door $744.95 Anneal Beads, Slump Bracelets and Fuse Tiles, Plates and Metal Clay - All in One Kiln. Our largest and most versatile table-top kiln, the Jen Ken 11-4.5 features a built-in 2 fiber bead door that makes annealing beads and intricate glass sculptures easy. Switch from annealing to fusing and slumping, creating glass bracelets and firing metal clay by placing the included removable kiln brick in the flip door opening for added thermal insulation. The EZ-Pro controller provides three button control at your fingertips. Pre-programmed with 8 firing schedules for glass, 3 firing schedules for batch annealing, plus a handy annealing hold cycle to anneal as you create. Along with 5 firing schedules for metal clay, it and 39;s simple to get started with any art. You can also customize and store up to 22 programs. From beginner to advanced artist, this kiln and controller packs all the features that matter. Covered by an incredible 2 year manufacturer warranty. PLUS it includes an Accessory Pack so you can start fusing right away. It includes the kiln shelf, stand, posts and shelf wash. Firing chamber measures 11 x 4-1/2 deep. See specifications for full product details. This kiln is able to ship UPS . Kiln Controllers Made Easy DVD Free Exclusively From Delphi. Let Delphi take the guesswork out of getting your kiln fired up. With the purchase of this kiln you will receive Delphi and 39;s exclusive DVD on programming kiln controllers for free. We will walk you through your first firing with close-up shots of your controller and explanations every step of the way. With an additional section on set-up and safety, getting started in fusing has never been easier.

Kidco Adjustable Locking Strap in White $5.95 The Kidco Adjustable Locking Strap is a great all-purpose child proofing solution for your home. Ideal for securing glass doors appliances lazy susans drawers and more the Kidco locking strap is a lifesaver in a home with young children. As a cabinet lock drawer lock or door lock the Kidco Adjustable Locking Strap works like a charm to keep kids out. The strap mounts easily with adhesive and features a flexible design that allows extension up to 8.5." The Kidco Adjustable Locking Strap comes in white or charcoal to suit nearly any space.S410-CHARCOAL - Kidco Adjustable Locking Strap in CharcoalS410-WHITE - Kidco Adjustable Locking Strap in White

Clear Texture / Architectural Bargain Glass Pack $41.95 Ten assorted pieces of Spectrum and 39;s wonderful clear textures, also referred to as architectural glass. Clear glass matches any decorating scheme. Ideal for background pieces, cabinet and door inserts, and more. Each piece is about 8 x 12. All glass is clearly marked with item numbers for easy reordering. There are no extra boxing charges for glass packs. Photo is one example. Actual glass may vary from photo. First cabinet project below from Kitchen Cabinets, Windows and Tile book 6200. Second cabinet by artist George Ayars. The third panel below combines bevels with multiple clear textures to create a design with lots of texture and visual appeal. From Creative Stained Glass book 6686. The circle and square styled panel is from Beveled Glass For Your Home book 5977.

Sierra Kiln With Viewing Window And Bead Door $849.95 The Perfect Kiln for Jewelry Artists. The Sierra 360 is not just for metal clay. Recently updated to include a bead door, this kiln is designed with all your jewelry projects in mind. The kiln features a digital controller, pre-programmed for use with metal clay, with a customizable 4 segment program for glass fusing or annealing. The pre-programmed settings for metal clay allow you to be successful with your kiln on the very first firing. The easy to use controller is preset with the most often used firing sequences for PMC, PMC+ and PMC3, yet is customizable for precise control. The 4 segment custom program option allows you complete flexibility. Store a program for bead annealing, glass fusing, or metal enameling and you and 39;ll be able to get even more use out of this incredible little kiln. The Sierra comes ready to go with a kiln shelf and four kiln posts. The ceramic fiber chamber is well insulated for optimal performance and durability. Firing chamber measures 8 x 6 x 8 deep. See specifications for full product details. This kiln is able to ship UPS . Create beautiful custom jewelry with the pre-set programs. Artist Melanie Churchill created the jewelry below. Kiln Controllers Made Easy DVD Free Exclusively From Delphi. Let Delphi take the guesswork out of getting your kiln fired up. With the purchase of this kiln you will receive Delphi and 39;s exclusive DVD on programming kiln controllers for free. We will walk you through your first firing with close-up shots of your controller and explanations every step of the way. With an additional section on set-up and safety, getting started in fusing has never been easier. Also available in 220/240V version. Click Here for pricing and information.

Skutt Gm10f Glass Kiln $1124.95 Double the Use. Double the Value. An amazing multi-purpose kiln. While perfect for annealing torch work beads, this kiln is also an excellent fusing kiln smaller projects. Features both a side hinged door and an easy-to-operate bead door (see image below). Doors have wooden handles mounted away from the heat which allows you to open them without gloves. The famed GlassMaster controller is standard on this unit. Designed specifically for glass fusing, you and 39;ll find it easier to use than typical controllers that were originally designed for ceramic work. The accurate and stable temperature provided by the controller is perfect for annealing. Extremely portable and works on standard household current (110 volts). Firing chamber measures 9 x 10 x 9 deep. See specifications for full product details. This kiln is able to ship UPS . Kiln Controllers Made Easy DVD Free Exclusively From Delphi. Let Delphi take the guesswork out of getting your kiln fired up. With the purchase of this kiln you will receive Delphi and 39;s exclusive DVD on programming kiln controllers for free. We will walk you through your first firing with close-up shots of your controller and explanations every step of the way. With an additional section on set-up and safety, getting started in fusing has never been easier.

Paragon Turquoise Sc-2 Kiln With Bead Door $769.95 Fusing is More Fun in Color Show your personality with Hot Color Kilns. Ideal for creating fused glass jewelry, firing metal clay and annealing lampworked beads. The Sentry Xpress 3-button digital controller holds up to 4 custom programs, with up to 8 segments each. Click View User Manual for illustrated instruction manual. Firing chamber measures 8 x 5-3/4 x 7-3/4 deep. See specifications for full product details. This kiln is able to ship UPS . Features of the Sentry Xpress 3-key Controller Design programs with up to 8 segments (steps) in Ramp-Hold mode. Fire to a single temperature at a single speed in the simplified Single Speed mode. Skip a segment in Ramp-Hold during firing without having to stop the kiln to reprogram. Change the target temperature in Ramp-Hold during firing without having to stop the kiln to reprogram. Add Hold Time during firing without having to stop the kiln to reprogram. Control both heating and cooling in Ramp-Hold. Program Review lets you check the program you are about to fire. Program the Temperature Alarm to sound when the kiln reaches a specific temperature. Use this to remind yourself to check on the kiln. Temperature display throughout firing and cooling in your choice of °F or °C Thermocouple Offset adjusts the thermocouple readout. Set the Delay to turn on the kiln later to suit your schedule. Error Messages report mechanical problems such as a disconnected thermocouple, stuck relay or broken element. LED Lights show whether you are in program, review, or firing mode. Kiln Controllers Made Easy DVD Free Exclusively From Delphi. Let Delphi take the guesswork out of getting your kiln fired up. With the purchase of this kiln you will receive Delphi and 39;s exclusive DVD on programming kiln controllers for free. We will walk you through your first firing with close-up shots of your controller and explanations every step of the way. With an additional section on set-up and safety, getting started in fusing has never been easier. Also available in 220/240V version. Click Here for pricing and information.

Paragon Blue Sc-2 Kiln With Bead Door $719.95 Ideal for creating fused glass jewelry, firing metal clay and annealing lampworked beads. The Sentry Xpress 3-button digital controller holds up to 4 custom programs, with up to 8 segments each. Click View User Manual for illustrated instruction manual. Firing chamber measures 8 x 5-3/4 x 7-3/4 deep. See specifications for full product details. This kiln is able to ship UPS . Features of the Sentry Xpress 3-key Controller Design programs with up to 8 segments (steps) in Ramp-Hold mode. Fire to a single temperature at a single speed in the simplified Single Speed mode. Skip a segment in Ramp-Hold during firing without having to stop the kiln to reprogram. Change the target temperature in Ramp-Hold during firing without having to stop the kiln to reprogram. Add Hold Time during firing without having to stop the kiln to reprogram. Control both heating and cooling in Ramp-Hold. Program Review lets you check the program you are about to fire. Program the Temperature Alarm to sound when the kiln reaches a specific temperature. Use this to remind yourself to check on the kiln. Temperature display throughout firing and cooling in your choice of °F or °C Thermocouple Offset adjusts the thermocouple readout. Set the Delay to turn on the kiln later to suit your schedule. Error Messages report mechanical problems such as a disconnected thermocouple, stuck relay or broken element. LED Lights show whether you are in program, review, or firing mode. Kiln Controllers Made Easy DVD Free Exclusively From Delphi. Let Delphi take the guesswork out of getting your kiln fired up. With the purchase of this kiln you will receive Delphi and 39;s exclusive DVD on programming kiln controllers for free. We will walk you through your first firing with close-up shots of your controller and explanations every step of the way. With an additional section on set-up and safety, getting started in fusing has never been easier. Also available in 220/240V version. Click Here for pricing and information.

Paragon Pink Sc-2 Kiln With Bead Door $769.95 Fusing is More Fun in Color Show your personality with Hot Color Kilns. Ideal for creating fused glass jewelry, firing metal clay and annealing lampworked beads. The Sentry Xpress 3-button digital controller holds up to 4 custom programs, with up to 8 segments each. Click View User Manual for illustrated instruction manual. Firing chamber measures 8 x 5-3/4 x 7-3/4 deep. See specifications for full product details. This kiln is able to ship UPS . Features of the Sentry Xpress 3-key Controller Design programs with up to 8 segments (steps) in Ramp-Hold mode. Fire to a single temperature at a single speed in the simplified Single Speed mode. Skip a segment in Ramp-Hold during firing without having to stop the kiln to reprogram. Change the target temperature in Ramp-Hold during firing without having to stop the kiln to reprogram. Add Hold Time during firing without having to stop the kiln to reprogram. Control both heating and cooling in Ramp-Hold. Program Review lets you check the program you are about to fire. Program the Temperature Alarm to sound when the kiln reaches a specific temperature. Use this to remind yourself to check on the kiln. Temperature display throughout firing and cooling in your choice of °F or °C Thermocouple Offset adjusts the thermocouple readout. Set the Delay to turn on the kiln later to suit your schedule. Error Messages report mechanical problems such as a disconnected thermocouple, stuck relay or broken element. LED Lights show whether you are in program, review, or firing mode. Kiln Controllers Made Easy DVD Free Exclusively From Delphi. Let Delphi take the guesswork out of getting your kiln fired up. With the purchase of this kiln you will receive Delphi and 39;s exclusive DVD on programming kiln controllers for free. We will walk you through your first firing with close-up shots of your controller and explanations every step of the way. With an additional section on set-up and safety, getting started in fusing has never been easier. Also available in 220/240V version. Click Here for pricing and information.

Paragon Purple Sc-2 Kiln With Bead Door $769.95 Fusing is More Fun in Color Show your personality with Hot Color Kilns. Ideal for creating fused glass jewelry, firing metal clay and annealing lampworked beads. The Sentry Xpress 3-button digital controller holds up to 4 custom programs, with up to 8 segments each. Click View User Manual for illustrated instruction manual. Firing chamber measures 8 x 5-3/4 x 7-3/4 deep. See specifications for full product details. This kiln is able to ship UPS . Features of the Sentry Xpress 3-key Controller Design programs with up to 8 segments (steps) in Ramp-Hold mode. Fire to a single temperature at a single speed in the simplified Single Speed mode. Skip a segment in Ramp-Hold during firing without having to stop the kiln to reprogram. Change the target temperature in Ramp-Hold during firing without having to stop the kiln to reprogram. Add Hold Time during firing without having to stop the kiln to reprogram. Control both heating and cooling in Ramp-Hold. Program Review lets you check the program you are about to fire. Program the Temperature Alarm to sound when the kiln reaches a specific temperature. Use this to remind yourself to check on the kiln. Temperature display throughout firing and cooling in your choice of °F or °C Thermocouple Offset adjusts the thermocouple readout. Set the Delay to turn on the kiln later to suit your schedule. Error Messages report mechanical problems such as a disconnected thermocouple, stuck relay or broken element. LED Lights show whether you are in program, review, or firing mode. Kiln Controllers Made Easy DVD Free Exclusively From Delphi. Let Delphi take the guesswork out of getting your kiln fired up. With the purchase of this kiln you will receive Delphi and 39;s exclusive DVD on programming kiln controllers for free. We will walk you through your first firing with close-up shots of your controller and explanations every step of the way. With an additional section on set-up and safety, getting started in fusing has never been easier. Also available in 220/240V version. Click Here for pricing and information.

Sierra Kiln With Viewing Window And Bead Door - International Voltage $849.95 The Perfect Kiln for Jewelry Artists. The Sierra 360 is not just for metal clay. Recently updated to include a bead door, this kiln is designed with all your jewelry projects in mind. The kiln features a digital controller, pre-programmed for use with metal clay, with a customizable 4 segment program for glass fusing or annealing. The pre-programmed settings for metal clay allow you to be successful with your kiln on the very first firing. The easy to use controller is preset with the most often used firing sequences for PMC, PMC+ and PMC3, yet is customizable for precise control. The 4 segment custom program option allows you complete flexibility. Store a program for bead annealing, glass fusing, or metal enameling and you and 39;ll be able to get even more use out of this incredible little kiln. It comes ready to go with a kiln shelf and four kiln posts. The ceramic fiber chamber is well insulated for optimal performance and durability. Firing chamber measures 8 x 6 x 8 deep. Made by Evenheat. 1 year manufacturer warranty. This tool is designed just for our international customers. This item uses international voltage of 220/240V, common in Europe and other parts of the world, but will not work with North American electrical outlets. For the standard American voltage product Click Here . Kiln Controllers Made Easy DVD Free Exclusively From Delphi. Let Delphi take the guesswork out of getting your kiln fired up. With the purchase of this kiln you will receive Delphi and 39;s exclusive DVD on programming kiln controllers for free. We will walk you through your first firing with close-up shots of your controller and explanations every step of the way. With an additional section on set-up and safety, getting started in fusing has never been easier. Project below was created by Melanie Churchill.

Paragon Turquoise Sc-2 Kiln With Viewing Window And Bead Door $799.95 Fusing is More Fun in Color Show your personality with Hot Color Kilns. Ideal for creating fused glass jewelry, firing metal clay and annealing lampworked beads. The Sentry Xpress 3-button digital controller holds up to 4 custom programs, with up to 8 segments each. Click View User Manual for illustrated instruction manual. Firing chamber measures 8 x 5-3/4 x 7-3/4 deep. See specifications for full product details. This kiln is able to ship UPS . Features of the Sentry Xpress 3-key Controller Design programs with up to 8 segments (steps) in Ramp-Hold mode. Fire to a single temperature at a single speed in the simplified Single Speed mode. Skip a segment in Ramp-Hold during firing without having to stop the kiln to reprogram. Change the target temperature in Ramp-Hold during firing without having to stop the kiln to reprogram. Add Hold Time during firing without having to stop the kiln to reprogram. Control both heating and cooling in Ramp-Hold. Program Review lets you check the program you are about to fire. Program the Temperature Alarm to sound when the kiln reaches a specific temperature. Use this to remind yourself to check on the kiln. Temperature display throughout firing and cooling in your choice of °F or °C Thermocouple Offset adjusts the thermocouple readout. Set the Delay to turn on the kiln later to suit your schedule. Error Messages report mechanical problems such as a disconnected thermocouple, stuck relay or broken element. LED Lights show whether you are in program, review, or firing mode. Kiln Controllers Made Easy DVD Free Exclusively From Delphi. Let Delphi take the guesswork out of getting your kiln fired up. With the purchase of this kiln you will receive Delphi and 39;s exclusive DVD on programming kiln controllers for free. We will walk you through your first firing with close-up shots of your controller and explanations every step of the way. With an additional section on set-up and safety, getting started in fusing has never been easier. Also available in 220/240V version. Click Here for pricing and information.

Paragon Purple Sc-2 Kiln With Viewing Window And Bead Door $799.95 Fusing is More Fun in Color Show your personality with Hot Color Kilns. Ideal for creating fused glass jewelry, firing metal clay and annealing lampworked beads. The Sentry Xpress 3-button digital controller holds up to 4 custom programs, with up to 8 segments each. Click View User Manual for illustrated instruction manual. Firing chamber measures 8 x 5-3/4 x 7-3/4 deep. See specifications for full product details. This kiln is able to ship UPS . Features of the Sentry Xpress 3-key Controller Design programs with up to 8 segments (steps) in Ramp-Hold mode. Fire to a single temperature at a single speed in the simplified Single Speed mode. Skip a segment in Ramp-Hold during firing without having to stop the kiln to reprogram. Change the target temperature in Ramp-Hold during firing without having to stop the kiln to reprogram. Add Hold Time during firing without having to stop the kiln to reprogram. Control both heating and cooling in Ramp-Hold. Program Review lets you check the program you are about to fire. Program the Temperature Alarm to sound when the kiln reaches a specific temperature. Use this to remind yourself to check on the kiln. Temperature display throughout firing and cooling in your choice of °F or °C Thermocouple Offset adjusts the thermocouple readout. Set the Delay to turn on the kiln later to suit your schedule. Error Messages report mechanical problems such as a disconnected thermocouple, stuck relay or broken element. LED Lights show whether you are in program, review, or firing mode. Kiln Controllers Made Easy DVD Free Exclusively From Delphi. Let Delphi take the guesswork out of getting your kiln fired up. With the purchase of this kiln you will receive Delphi and 39;s exclusive DVD on programming kiln controllers for free. We will walk you through your first firing with close-up shots of your controller and explanations every step of the way. With an additional section on set-up and safety, getting started in fusing has never been easier. Also available in 220/240V version. Click Here for pricing and information.

Paragon Blue Sc-2 Kiln With Viewing Window And Bead Door $749.95 Ideal for creating fused glass jewelry, firing metal clay and annealing lampworked beads. The Sentry Xpress 3-button digital controller holds up to 4 custom programs, with up to 8 segments each. Click View User Manual for illustrated instruction manual. Firing chamber measures 8 x 5-3/4 x 7-3/4 deep. See specifications for full product details. This kiln is able to ship UPS . Features of the Sentry Xpress 3-key Controller Design programs with up to 8 segments (steps) in Ramp-Hold mode. Fire to a single temperature at a single speed in the simplified Single Speed mode. Skip a segment in Ramp-Hold during firing without having to stop the kiln to reprogram. Change the target temperature in Ramp-Hold during firing without having to stop the kiln to reprogram. Add Hold Time during firing without having to stop the kiln to reprogram. Control both heating and cooling in Ramp-Hold. Program Review lets you check the program you are about to fire. Program the Temperature Alarm to sound when the kiln reaches a specific temperature. Use this to remind yourself to check on the kiln. Temperature display throughout firing and cooling in your choice of °F or °C Thermocouple Offset adjusts the thermocouple readout. Set the Delay to turn on the kiln later to suit your schedule. Error Messages report mechanical problems such as a disconnected thermocouple, stuck relay or broken element. LED Lights show whether you are in program, review, or firing mode. Kiln Controllers Made Easy DVD Free Exclusively From Delphi. Let Delphi take the guesswork out of getting your kiln fired up. With the purchase of this kiln you will receive Delphi and 39;s exclusive DVD on programming kiln controllers for free. We will walk you through your first firing with close-up shots of your controller and explanations every step of the way. With an additional section on set-up and safety, getting started in fusing has never been easier. Also available in 220/240V version. Click Here for pricing and information.

Paragon Pink Sc-2 Kiln With Viewing Window And Bead Door $799.95 Fusing is More Fun in Color Show your personality with Hot Color Kilns. Ideal for creating fused glass jewelry, firing metal clay and annealing lampworked beads. The Sentry Xpress 3-button digital controller holds up to 4 custom programs, with up to 8 segments each. Click View User Manual for illustrated instruction manual. Firing chamber measures 8 x 5-3/4 x 7-3/4 deep. See specifications for full product details. This kiln is able to ship UPS . Features of the Sentry Xpress 3-key Controller Design programs with up to 8 segments (steps) in Ramp-Hold mode. Fire to a single temperature at a single speed in the simplified Single Speed mode. Skip a segment in Ramp-Hold during firing without having to stop the kiln to reprogram. Change the target temperature in Ramp-Hold during firing without having to stop the kiln to reprogram. Add Hold Time during firing without having to stop the kiln to reprogram. Control both heating and cooling in Ramp-Hold. Program Review lets you check the program you are about to fire. Program the Temperature Alarm to sound when the kiln reaches a specific temperature. Use this to remind yourself to check on the kiln. Temperature display throughout firing and cooling in your choice of °F or °C Thermocouple Offset adjusts the thermocouple readout. Set the Delay to turn on the kiln later to suit your schedule. Error Messages report mechanical problems such as a disconnected thermocouple, stuck relay or broken element. LED Lights show whether you are in program, review, or firing mode. Kiln Controllers Made Easy DVD Free Exclusively From Delphi. Let Delphi take the guesswork out of getting your kiln fired up. With the purchase of this kiln you will receive Delphi and 39;s exclusive DVD on programming kiln controllers for free. We will walk you through your first firing with close-up shots of your controller and explanations every step of the way. With an additional section on set-up and safety, getting started in fusing has never been easier. Also available in 220/240V version. Click Here for pricing and information.

Paragon Purple Sc-2 Kiln With Bead Door - International Voltage $769.95 Fusing is More Fun in Color Show your personality with Hot Color Kilns. Ideal for creating fused glass jewelry, firing metal clay and annealing lampworked beads. The Sentry Xpress 3-button digital controller holds up to 4 custom programs, with up to 8 segments each. Click View User Manual for illustrated instruction manual. Firing chamber measures 8 x 5-3/4 x 7-3/4 deep. See specifications for full product details. This kiln is able to ship UPS . Features of the Sentry Xpress 3-key Controller Design programs with up to 8 segments (steps) in Ramp-Hold mode. Fire to a single temperature at a single speed in the simplified Single Speed mode. Skip a segment in Ramp-Hold during firing without having to stop the kiln to reprogram. Change the target temperature in Ramp-Hold during firing without having to stop the kiln to reprogram. Add Hold Time during firing without having to stop the kiln to reprogram. Control both heating and cooling in Ramp-Hold. Program Review lets you check the program you are about to fire. Program the Temperature Alarm to sound when the kiln reaches a specific temperature. Use this to remind yourself to check on the kiln. Temperature display throughout firing and cooling in your choice of °F or °C Thermocouple Offset adjusts the thermocouple readout. Set the Delay to turn on the kiln later to suit your schedule. Error Messages report mechanical problems such as a disconnected thermocouple, stuck relay or broken element. LED Lights show whether you are in program, review, or firing mode. Kiln Controllers Made Easy DVD Free Exclusively From Delphi. Let Delphi take the guesswork out of getting your kiln fired up. With the purchase of this kiln you will receive Delphi and 39;s exclusive DVD on programming kiln controllers for free. We will walk you through your first firing with close-up shots of your controller and explanations every step of the way. With an additional section on set-up and safety, getting started in fusing has never been easier. This tool is designed just for our international customers. This item uses international voltage of 220/240V, common in Europe and other parts of the world, but will not work with North American electrical outlets. For the standard American voltage product For the standard American voltage product Click Here .

Paragon Blue Sc-2 Kiln With Viewing Window And Bead Door - International Voltage $749.95 Ideal for creating fused glass jewelry, firing metal clay and annealing lampworked beads. The Sentry Xpress 3-button digital controller holds up to 4 custom programs, with up to 8 segments each. Click View User Manual for illustrated instruction manual. Firing chamber measures 8 x 5-3/4 x 7-3/4 deep. See specifications for full product details. This kiln is able to ship UPS . Features of the Sentry Xpress 3-key Controller Design programs with up to 8 segments (steps) in Ramp-Hold mode. Fire to a single temperature at a single speed in the simplified Single Speed mode. Skip a segment in Ramp-Hold during firing without having to stop the kiln to reprogram. Change the target temperature in Ramp-Hold during firing without having to stop the kiln to reprogram. Add Hold Time during firing without having to stop the kiln to reprogram. Control both heating and cooling in Ramp-Hold. Program Review lets you check the program you are about to fire. Program the Temperature Alarm to sound when the kiln reaches a specific temperature. Use this to remind yourself to check on the kiln. Temperature display throughout firing and cooling in your choice of °F or °C Thermocouple Offset adjusts the thermocouple readout. Set the Delay to turn on the kiln later to suit your schedule. Error Messages report mechanical problems such as a disconnected thermocouple, stuck relay or broken element. LED Lights show whether you are in program, review, or firing mode. Kiln Controllers Made Easy DVD Free Exclusively From Delphi. Let Delphi take the guesswork out of getting your kiln fired up. With the purchase of this kiln you will receive Delphi and 39;s exclusive DVD on programming kiln controllers for free. We will walk you through your first firing with close-up shots of your controller and explanations every step of the way. With an additional section on set-up and safety, getting started in fusing has never been easier. This tool is designed just for our international customers. This item uses international voltage of 220/240V, common in Europe and other parts of the world, but will not work with North American electrical outlets. For the standard American voltage product For the standard American voltage product Click Here .

Paragon Turquoise Sc-2 Kiln With Viewing Window And Bead Door - International Voltage $799.95 Fusing is More Fun in Color Show your personality with Hot Color Kilns. Ideal for creating fused glass jewelry, firing metal clay and annealing lampworked beads. The Sentry Xpress 3-button digital controller holds up to 4 custom programs, with up to 8 segments each. Click View User Manual for illustrated instruction manual. Firing chamber measures 8 x 5-3/4 x 7-3/4 deep. See specifications for full product details. This kiln is able to ship UPS . Features of the Sentry Xpress 3-key Controller Design programs with up to 8 segments (steps) in Ramp-Hold mode. Fire to a single temperature at a single speed in the simplified Single Speed mode. Skip a segment in Ramp-Hold during firing without having to stop the kiln to reprogram. Change the target temperature in Ramp-Hold during firing without having to stop the kiln to reprogram. Add Hold Time during firing without having to stop the kiln to reprogram. Control both heating and cooling in Ramp-Hold. Program Review lets you check the program you are about to fire. Program the Temperature Alarm to sound when the kiln reaches a specific temperature. Use this to remind yourself to check on the kiln. Temperature display throughout firing and cooling in your choice of °F or °C Thermocouple Offset adjusts the thermocouple readout. Set the Delay to turn on the kiln later to suit your schedule. Error Messages report mechanical problems such as a disconnected thermocouple, stuck relay or broken element. LED Lights show whether you are in program, review, or firing mode. Kiln Controllers Made Easy DVD Free Exclusively From Delphi. Let Delphi take the guesswork out of getting your kiln fired up. With the purchase of this kiln you will receive Delphi and 39;s exclusive DVD on programming kiln controllers for free. We will walk you through your first firing with close-up shots of your controller and explanations every step of the way. With an additional section on set-up and safety, getting started in fusing has never been easier. This tool is designed just for our international customers. This item uses international voltage of 220/240V, common in Europe and other parts of the world, but will not work with North American electrical outlets. For the standard American voltage product For the standard American voltage product Click Here .

Paragon Blue Sc-2 Kiln With Bead Door - International Voltage $719.95 Ideal for creating fused glass jewelry, firing metal clay and annealing lampworked beads. The Sentry Xpress 3-button digital controller holds up to 4 custom programs, with up to 8 segments each. Click View User Manual for illustrated instruction manual. Firing chamber measures 8 x 5-3/4 x 7-3/4 deep. See specifications for full product details. This kiln is able to ship UPS . Features of the Sentry Xpress 3-key Controller Design programs with up to 8 segments (steps) in Ramp-Hold mode. Fire to a single temperature at a single speed in the simplified Single Speed mode. Skip a segment in Ramp-Hold during firing without having to stop the kiln to reprogram. Change the target temperature in Ramp-Hold during firing without having to stop the kiln to reprogram. Add Hold Time during firing without having to stop the kiln to reprogram. Control both heating and cooling in Ramp-Hold. Program Review lets you check the program you are about to fire. Program the Temperature Alarm to sound when the kiln reaches a specific temperature. Use this to remind yourself to check on the kiln. Temperature display throughout firing and cooling in your choice of °F or °C Thermocouple Offset adjusts the thermocouple readout. Set the Delay to turn on the kiln later to suit your schedule. Error Messages report mechanical problems such as a disconnected thermocouple, stuck relay or broken element. LED Lights show whether you are in program, review, or firing mode. Kiln Controllers Made Easy DVD Free Exclusively From Delphi. Let Delphi take the guesswork out of getting your kiln fired up. With the purchase of this kiln you will receive Delphi and 39;s exclusive DVD on programming kiln controllers for free. We will walk you through your first firing with close-up shots of your controller and explanations every step of the way. With an additional section on set-up and safety, getting started in fusing has never been easier. This tool is designed just for our international customers. This item uses international voltage of 220/240V, common in Europe and other parts of the world, but will not work with North American electrical outlets. For the standard American voltage product For the standard American voltage product Click Here .

Paragon Pink Sc-2 Kiln With Bead Door - International Voltage $769.95 Fusing is More Fun in Color Show your personality with Hot Color Kilns. Ideal for creating fused glass jewelry, firing metal clay and annealing lampworked beads. The Sentry Xpress 3-button digital controller holds up to 4 custom programs, with up to 8 segments each. Click View User Manual for illustrated instruction manual. Firing chamber measures 8 x 5-3/4 x 7-3/4 deep. See specifications for full product details. This kiln is able to ship UPS . Features of the Sentry Xpress 3-key Controller Design programs with up to 8 segments (steps) in Ramp-Hold mode. Fire to a single temperature at a single speed in the simplified Single Speed mode. Skip a segment in Ramp-Hold during firing without having to stop the kiln to reprogram. Change the target temperature in Ramp-Hold during firing without having to stop the kiln to reprogram. Add Hold Time during firing without having to stop the kiln to reprogram. Control both heating and cooling in Ramp-Hold. Program Review lets you check the program you are about to fire. Program the Temperature Alarm to sound when the kiln reaches a specific temperature. Use this to remind yourself to check on the kiln. Temperature display throughout firing and cooling in your choice of °F or °C Thermocouple Offset adjusts the thermocouple readout. Set the Delay to turn on the kiln later to suit your schedule. Error Messages report mechanical problems such as a disconnected thermocouple, stuck relay or broken element. LED Lights show whether you are in program, review, or firing mode. Kiln Controllers Made Easy DVD Free Exclusively From Delphi. Let Delphi take the guesswork out of getting your kiln fired up. With the purchase of this kiln you will receive Delphi and 39;s exclusive DVD on programming kiln controllers for free. We will walk you through your first firing with close-up shots of your controller and explanations every step of the way. With an additional section on set-up and safety, getting started in fusing has never been easier. This tool is designed just for our international customers. This item uses international voltage of 220/240V, common in Europe and other parts of the world, but will not work with North American electrical outlets. For the standard American voltage product For the standard American voltage product Click Here .

Paragon Turquoise Sc-2 Kiln With Bead Door - International Voltage $769.95 Fusing is More Fun in Color Show your personality with Hot Color Kilns. Ideal for creating fused glass jewelry, firing metal clay and annealing lampworked beads. The Sentry Xpress 3-button digital controller holds up to 4 custom programs, with up to 8 segments each. Click View User Manual for illustrated instruction manual. Firing chamber measures 8 x 5-3/4 x 7-3/4 deep. See specifications for full product details. This kiln is able to ship UPS . Features of the Sentry Xpress 3-key Controller Design programs with up to 8 segments (steps) in Ramp-Hold mode. Fire to a single temperature at a single speed in the simplified Single Speed mode. Skip a segment in Ramp-Hold during firing without having to stop the kiln to reprogram. Change the target temperature in Ramp-Hold during firing without having to stop the kiln to reprogram. Add Hold Time during firing without having to stop the kiln to reprogram. Control both heating and cooling in Ramp-Hold. Program Review lets you check the program you are about to fire. Program the Temperature Alarm to sound when the kiln reaches a specific temperature. Use this to remind yourself to check on the kiln. Temperature display throughout firing and cooling in your choice of °F or °C Thermocouple Offset adjusts the thermocouple readout. Set the Delay to turn on the kiln later to suit your schedule. Error Messages report mechanical problems such as a disconnected thermocouple, stuck relay or broken element. LED Lights show whether you are in program, review, or firing mode. Kiln Controllers Made Easy DVD Free Exclusively From Delphi. Let Delphi take the guesswork out of getting your kiln fired up. With the purchase of this kiln you will receive Delphi and 39;s exclusive DVD on programming kiln controllers for free. We will walk you through your first firing with close-up shots of your controller and explanations every step of the way. With an additional section on set-up and safety, getting started in fusing has never been easier. This tool is designed just for our international customers. This item uses international voltage of 220/240V, common in Europe and other parts of the world, but will not work with North American electrical outlets. For the standard American voltage product For the standard American voltage product Click Here .

Paragon Pink Sc-2 Kiln With Viewing Window And Bead Door - International Voltage $799.95 Fusing is More Fun in Color Show your personality with Hot Color Kilns. Ideal for creating fused glass jewelry, firing metal clay and annealing lampworked beads. The Sentry Xpress 3-button digital controller holds up to 4 custom programs, with up to 8 segments each. Click View User Manual for illustrated instruction manual. Firing chamber measures 8 x 5-3/4 x 7-3/4 deep. See specifications for full product details. This kiln is able to ship UPS . Features of the Sentry Xpress 3-key Controller Design programs with up to 8 segments (steps) in Ramp-Hold mode. Fire to a single temperature at a single speed in the simplified Single Speed mode. Skip a segment in Ramp-Hold during firing without having to stop the kiln to reprogram. Change the target temperature in Ramp-Hold during firing without having to stop the kiln to reprogram. Add Hold Time during firing without having to stop the kiln to reprogram. Control both heating and cooling in Ramp-Hold. Program Review lets you check the program you are about to fire. Program the Temperature Alarm to sound when the kiln reaches a specific temperature. Use this to remind yourself to check on the kiln. Temperature display throughout firing and cooling in your choice of °F or °C Thermocouple Offset adjusts the thermocouple readout. Set the Delay to turn on the kiln later to suit your schedule. Error Messages report mechanical problems such as a disconnected thermocouple, stuck relay or broken element. LED Lights show whether you are in program, review, or firing mode. Kiln Controllers Made Easy DVD Free Exclusively From Delphi. Let Delphi take the guesswork out of getting your kiln fired up. With the purchase of this kiln you will receive Delphi and 39;s exclusive DVD on programming kiln controllers for free. We will walk you through your first firing with close-up shots of your controller and explanations every step of the way. With an additional section on set-up and safety, getting started in fusing has never been easier. This tool is designed just for our international customers. This item uses international voltage of 220/240V, common in Europe and other parts of the world, but will not work with North American electrical outlets. For the standard American voltage product For the standard American voltage product Click Here .

Paragon Purple Sc-2 Kiln With Viewing Window And Bead Door - International Voltage $799.95 Fusing is More Fun in Color Show your personality with Hot Color Kilns. Ideal for creating fused glass jewelry, firing metal clay and annealing lampworked beads. The Sentry Xpress 3-button digital controller holds up to 4 custom programs, with up to 8 segments each. Click View User Manual for illustrated instruction manual. Firing chamber measures 8 x 5-3/4 x 7-3/4 deep. See specifications for full product details. This kiln is able to ship UPS . Features of the Sentry Xpress 3-key Controller Design programs with up to 8 segments (steps) in Ramp-Hold mode. Fire to a single temperature at a single speed in the simplified Single Speed mode. Skip a segment in Ramp-Hold during firing without having to stop the kiln to reprogram. Change the target temperature in Ramp-Hold during firing without having to stop the kiln to reprogram. Add Hold Time during firing without having to stop the kiln to reprogram. Control both heating and cooling in Ramp-Hold. Program Review lets you check the program you are about to fire. Program the Temperature Alarm to sound when the kiln reaches a specific temperature. Use this to remind yourself to check on the kiln. Temperature display throughout firing and cooling in your choice of °F or °C Thermocouple Offset adjusts the thermocouple readout. Set the Delay to turn on the kiln later to suit your schedule. Error Messages report mechanical problems such as a disconnected thermocouple, stuck relay or broken element. LED Lights show whether you are in program, review, or firing mode. Kiln Controllers Made Easy DVD Free Exclusively From Delphi. Let Delphi take the guesswork out of getting your kiln fired up. With the purchase of this kiln you will receive Delphi and 39;s exclusive DVD on programming kiln controllers for free. We will walk you through your first firing with close-up shots of your controller and explanations every step of the way. With an additional section on set-up and safety, getting started in fusing has never been easier. This tool is designed just for our international customers. This item uses international voltage of 220/240V, common in Europe and other parts of the world, but will not work with North American electrical outlets. For the standard American voltage product For the standard American voltage product Click Here .

4-1/2 X 9 Star Bevel $8.95 Large star-shaped bevel. 4-/12 wide by 9 high. One piece. Ideal for the centerpiece of a stained glass window or beveled glass door.

Sparco Fuel Door - Locking (Chrome) [Universal - Fits all Vehicles] $179 Sparco Fuel Door - Locking (Chrome)

This entry was posted on Thursday, August 2nd, 2007 at 11:30 pm and is filed under Uncategorized. You can follow any responses to this entry through the RSS 2.0 feed. You can leave a response, or trackback from your own site.