Industrial Ethernet Switches

Power over Ethernet

Advantages over other integrated data and power standards

This technology is especially useful for powering IP telephones, wireless LAN access points, cameras with pan tilt and zoom (PTZ), remote Ethernet switches, embedded computers, thin clients and LCDs.

All these require more power than USB offers and very often must be powered over longer runs of cable than USB permits. In addition, PoE uses only one type of connector, an 8P8C (RJ45), whereas there are four different types of USB connectors.

PoE is presently deployed in applications where USB is unsuitable and where AC power would be inconvenient, expensive (mains wiring must often be done by qualified and/or licensed electricians for legal or insurance reasons) or infeasible to supply. However, even where USB or AC power could be used, PoE has several advantages over either, including the following:

Cheaper cabling  even category 5 cable is cheaper than USB repeaters, and the task of meeting building code requirements to run AC power cable is eliminated.

A Gigabit of data per second to every device is possible, which exceeds 2009 USB and the AC powerline networking capabilities.

Global organizations can deploy PoE everywhere without concern for any local variance in AC power standards, outlets, plugs, or reliability.

Direct injection from standard 48 V DC battery power arrays; this enables critical infrastructure to run more easily in outages, and make power rationing decisions centrally for all the PoE devices.

Symmetric distribution is possible. Unlike USB and AC outlets, power can be supplied at either end of the cable or outlet. This means the location of the power source can be determined after cables and outlets are installed.

Power management feature and integration

Most advocates expect PoE to become a global longterm DC power cabling standard and replace "wall wart" converters, which cannot be easily centrally managed, waste energy, are often poorly designed, and are easily vulnerable to damage from surges and brownouts. A combination of G.9960 networking on existing AC power lines to an outlet where a PoE router is plugged in is capable of moving a gigabit per second to every device, with minimal wiring and participating fully in both AC and DC device power demand management.

Integration with the IEEE 802.3az standard, the energy management capabilities of the combined standard are expected to be formidable. However, that integration has not yet occurred.

There are several PoE implementations, including ad-hoc techniques, but using the IEEE standard for supplying power over Ethernet is strongly recommended.

Nortel 5520 switch with 48 Power over Ethernet ports

IEEE 802.3af / 802.3at Power over Ethernet

Power over Ethernet is usually implemented following the specifications in IEEE std. 802.3af-2003 which added clause 33 to the IEEE 802.3 standard. It allows the powering device to use a voltage between 4457 V DC, though the nominal voltage is 48 V, over two of the four available pairs on a Cat. 3/Cat. 5e cable with a selectable current of 10350 mA subject to a maximum load power of 15.40 W. Only about 12.95 W are available after counting cable losses, and most switched power supplies will lose another 1025% of the available power. A "phantom power" technique is used to allow the powered pairs to also carry data. This permits its use not only with 10BASE-T and 100BASE-TX, which use only two of the four pairs in the cable, but also with 1000BASE-T (gigabit Ethernet), which uses all four pairs for data transmission. This is possible because all versions of Ethernet over twisted pair cable specify differential data transmission over each pair with transformer coupling; the DC supply and load connections can be made to the transformer center-taps at each end. Each pair thus operates in "common mode" as one side of the DC supply, so two pairs are required to complete the circuit. The polarity of the DC supply may be inverted by cross cables; the powered device must operate with either pair: spare pairs 4-5 and 7-8 or data pairs 1-2 and 3-6. Polarity is required on data pairs, and ambiguously implemented for spare pairs, with the use of a bridge rectifier.

The standard describes two types of devices: power sourcing equipment (PSE) and powered devices (PD). Power sourcing equipment provides power to the powered devices.

The newly released IEEE std. IEEE 802.3at-2009 amendment enhanced Power over Ethernet Category 5 cable to dynamically provide between 0.125 W of power.

Please help improve this article by expanding it. Further information might be found on the talk page. (October 2009)

Powering devices

Two modes, A and B, are available.

Mode A has two alternate configurations (MDI and MDI-X), using the same pairs but with different polarities. In mode A, pins 1-2 (pair #2 in T568B wiring) form one side of the 48 V DC, and pins 3-6 (pair #3 in T568B) form the other side. These are the same two pairs used for data transmission in 10Base-T and 100Base-TX, allowing the provision of both power and data over only two pairs in such networks. The free polarity allows for patch cables and automatic RX/TX detection.

In mode B, pins 4-5 (pair #1 in both T568A and T568B) form one side of the DC supply and pins 7-8 (pair #4 in both T568A and T568B) provide the return; these are the "spare" pairs in 10BASE-T and 100BASE-TX. Mode B, therefore, requires a 4-pair cable.

The PSE decides whether power mode A or B shall be used, not the powered device (PD). PDs that implement only Mode A or Mode B are specifically not allowed by the standard.

The PSE can implement mode A or B or both (but must not supply power in both modes at the same time). A PD indicates that it is standards-compliant by placing a 25 k resistor between the powered pairs. If the PSE detects a resistance that is too high or too low (including a short circuit), no power is applied. This protects devices that do not support IEEE 802.3af. An optional "power class" feature allows the PD to indicate its power requirements by changing the sense resistance at higher voltages. To stay powered, the PD must continuously use 510 mA for at least 60 ms with no less than 400 ms since last use or else it will be unpowered by the PSE.

There are two types of PSEs specified by IEEE 802.3-2008: endspans and midspans. Endspans are Ethernet switches that include the power over Ethernet transmission circuitry. Endspans are commonly called PoE switches. Midspans are power injectors that stand between a regular Ethernet switch and the powered device, injecting power without affecting the data. Endspans are normally used on new installations or when the switch has to be replaced for other reasons (such as moving from 10/100 Mbit/s to 1 Gbit/s or adding security protocols), which makes it convenient to add the PoE capability. Midspans are used when there is no desire to replace and configure a new Ethernet switch, and only PoE needs to be added to the network.

Stages of powering up a PoE link

Stage

Action

Volts specified

[V]

802.3af

802.3at

Detection

PSE detects if the PD has the correct signature resistance of 15 - 33 k

2.7 - 10.0

Classification

PSE detects resistor indicating power range (see below)

14.5 - 20.5

Mark 1

Signals PSE is 802.3at capable. PD presents a 0.25 - 4 mA load.

-

7 - 10

Class 2

PSE output classification voltage again to indicate 802.3at capability

-

14.5 - 20.5

Mark 2

Signals PSE is 802.3at capable. PD presents a 0.25 - 4 mA load.

-

7 - 10

Startup

Startup voltage

> 42

> 37.2

Normal operation

Supply power to device

44 - 57

30 - 58.6

IEEE 802.3at capable devices are also referred to as "type 2". An 802.3at PSE may also use layer2 communication to signal 802.3at capability.

Power levels available

Class

Usage

Classification current

[mA]

Power range

[Watt]

Class description

0

Default

0 - 4

0.44 - 12.94

Classification unimplemented

1

Optional

9 - 12

0.44 - 3.84

Low power

2

Optional

17 - 20

3.84 - 6.49

Mid power

3

Optional

26 - 30

6.49 - 12.95

High power

4

Reserved

36 - 44

Reserved

PSEs classify as Class 0

For IEEE 802.3at (type 2) devices class 4 instead of Reserved has a power range of 12.95 - 25.5 W.

Configuration via Ethernet layer 2 LLDP

LLDP-MED Advanced Power Management

TLV Header

MED Header

Extended power via MDI

Type  

(7 bits)

Length

(9 bits)

TIA OUI  

(3 octets)

Extended power via MDI subtype 

(1 octet)

Power type 

(2 bits)

Power source 

(2 bits)

Power priority 

(4 bits)

Power value 

(2 octets)

127

7

00-12-BB

4

PSE or PD

Normal or Backup conservation

Critical,

High,

Low

0 - 102,3 W in 0,1 steps

The setup phases are as follows:

PSE (provider) tests PD (consumer) physically using 802.3af phase class 3.

PSE powers up PD.

PD sends to PSE: I'm a PD, max power = X, max power requested = X.

PSE sends to PD: I'm a PSE , max power allowed = X.

PD may now use the amount of power as specified by the PSE.

The rules for this power negotiation are:

PD shall never request more power than physical 802.3af class

PD shall never draw more than max power advertised by PSE

PSE may deny any PD drawing more power than max allowed by PSE

PSE shall not reduce power allocated to PD, that is in use

PSE may request reduced power, via conservation mode

Non-standard implementations

Cisco

Cisco's original PoE equipment was manufactured many years before there was an IEEE standard for delivering PoE. Cisco's original PoE equipment was capable of delivering up to 10 W per port. The amount of power to be delivered is negotiated between the endpoint and the Cisco switch based on a power value that was added to the Cisco proprietary Cisco Discovery Protocol (CDP). CDP is also responsible for dynamically communicating the Voice VLAN value from the Cisco switch to the Cisco IP Phone.

The PSE (switch) will send a Fast Link Pulse (FLP) on the transmit pair. The PD (device) connects the transmit line to the receive line via an low pass filter. And thus the PSE gets the FLP in return. And a common mode current between pair 1 and 2 will be provided resulting in 48 V DC and 6.3 W default of allocated power. The PD has then to provide Ethernet link within 5 seconds to the auto-negotiation mode switch port. A later CDP message with a type-length-value tells the PSE it's final power requirement. A discontinued link pulses shuts down power.

Cisco manufactured 13 different devices, like, WLAN access points and IP phones that were not compliant with the IEEE 802.3-2005 Clause 33.

Cisco pre-standard IP phones

7985G, 7960G, 7940G, 7910G, 7910G + SW, 7912G, 7905G, 7902G, 7970G

Cisco IEEE 802.3af IP phones

7961G, 7961G-GE, 7971G-GE, 7931G, 7937G, 7941G, 7941G-GE, 7945G, 7965G, 7975G, 7985G

Cisco IEEE 802.3af and pre-standard IP phones

7970G, 7961G, 7906G, 7941G, 7911G, 7962G

The Cisco 7936 Conference Phone does not support any LAN based power and requires a Cisco power injection adapter. Cisco's original PoE implementation is not software upgradeable to the IEEE 802.3af standard.

3Com

Sold a midspan solution called "Ethernet Power Source" in 2000 - 2004 used with then current 3Com NBX phones, Access points, and Network jack switches. It measured a capacitance signature, and then provided -24 V DC.

Notes

Category 5e cable uses 24 AWG conductors, which can safely carry 360 mA at 50 V according to the latest TIA ruling.[citation needed] The cable has eight conductors (only half of which are used for power) and therefore the absolute maximum power transmitted using direct current is 50 V 0.360 A 2 = 36 W. Considering the voltage drop after 100 m, a PD would be able to receive 31.6 W. The additional heat generated in the wires by PoE at this current level (4.4 watts per 100 meter cable) limits the total number of cables in a bundle to be 100? at 45 C, according to the TIA.

Drawbacks of IEEE 802.3af are:

Excessive voltage with a peak at 60 V (many standard components are limited to ~30 V).

Undefined polarity (requires a diode bridge which causes a voltage drop and require more board space and components).

Undefined wire pairs (multiple configurations must be handled which requires more board space and components) (The diode bridge will waste 0.74 W at 25.5 W operation)

A partial solution to the drawbacks of IEEE 802.3af is to assume pin 4 + 5 as positive (+) and pin 7 + 8 as negative (-). This would not be standards compliant but will make PD implementation easier and not damage anything. Any incompatibilities with IEEE 802.3af will only result in an unpowered device.

The 0.74W waste in the diode bridge, above, assumes the use of standard rectifier diodes. If Schottky diodes are used, the waste will be half that much. In either case, the waste is much less than the losses in the DC-DC converter that must be used to convert the power to the low voltages used in the PD logic circuits.

802.3af Standards A and B

PINS on Switch

    10/100 DC on Spares    

    10/100 Mixed DC & Data    

    1000 Gigabit DC & Bi-Data    

Pin 1

Rx +

Rx +             DC +

TxRx A +             DC +

Pin 2

Rx -

Rx -              DC +

TxRx A -              DC +

Pin 3

Tx +

Tx +             DC -

TxRx B +             DC -

Pin 4

DC +

unused

TxRx C +

Pin 5

DC +

unused

TxRx C -

Pin 6

Tx -

Tx -             DC -

TxRx B -             DC -

Pin 7

DC -

unused

TxRx D +

Pin 8

DC -

unused

TxRx D -

Another modification is to limit voltage from the PSE to 30 V and thus enable the use of standard components. But this may destroy the PD if it is connected to a PSE that isn't modified to keep the voltage low enough. It also limits the amount of power that can be used.

Terminology

Power Sourcing Equipment (PSE)

Power Sourcing Equipment is a device (switch or hub for instance) that will provide power in a PoE setup. Maximum allowed continuous output power per such device in IEEE 802.3af is 15.40 W.

When the device is a switch, it's called an endspan. Else, if it's an intermediary device between a non PoE capable switch and a PoE device, it's called a midspan.

Powered Device (PD)

A powered device is a device powered by a PSE and thus consumes energy. Examples include wireless access points, IP Phones, and IP cameras. The IEEE 802.3af standard specifies a maximum power usage of 12.95 W.

Many powered devices have another connector for an optional auxiliary power supply. If used, this gives backup power to the device if the power to the Ethernet connector is inadequate or suddenly fails.

See also

Network switch, connects network nodes with independent pipes (efficient).

Category 5 cable

Power line communication, data communication over mains electricity.

Switched-mode power supply, efficient electrical power conversion.

ITU-T G.hn, a standard that provides a way to create a high-speed (up to 1 Gigabit/s) Local area network using existing home wiring (power lines, phone lines and coaxial cables).

Phantom power, long established standard technique to power microphones.

HomePlug Powerline Alliance, an industry trade group on datacommunication over mains electricity.

References

^ IEEE 802.3-2005, section 2, table 33-5, item 14

^ IEEE 802.3-2005, section 2, table 33-5, item 1

^ IEEE 802.3-2005, section 2, table 33-5, item 4

^ IEEE 802.3-2005, section 2, clause 33.3.5.2

^ a b http://standards.ieee.org/announcements/stdbd_approves_ieee802.3at.html

^ http://blog.tmcnet.com/blog/tom-keating/voip/8023at-2009-power-over-ethernet-poe-plus-standard-ratified.asp

^ Banish Those "Wall Warts" With Power Over Ethernet

^ a b c d "LTC4278 IEEE 802.3at PD with Synchronous No-Opto Flyback Controller and 12V Aux Support". http://cds.linear.com/docs/Datasheet/4278fa.pdf.  2010-01-11 cds.linear.com

^ a b IEEE 802.3-2005, section 2, table 33-3

^ a b "LLDP / LLDP-MED Proposal for PoE Plus (2006-09-15)". http://www.ieee802.org/1/files/public/docs2006/ab-congdon-lldp-med-8023at-0906.pdf. 2010-01-10

^ "Planning for Cisco IP Telephony > Network Infrastructure Analysis". http://www.ciscopress.com/articles/article.asp?p=385336&seqNum=2&rll=1.  2010-01-12 ciscopress.com

^ "Power over Ethernet on the Cisco Catalyst 6500 Series Switch". http://www.conticomp.com/PDF/CAT6500POE_ds.pdf.  2010-01-12 conticomp.com

^ "Understanding the Cisco IP Phone 10/100 Ethernet In-Line Power Detection Algorithm - Cisco Systems". http://www.cisco.com/en/US/products/hw/phones/ps379/products_tech_note09186a00801189b5.shtml.  2010-01-12 cisco.com

^ "Power over Ethernet (PoE) Power Requirements FAQ". http://www.cisco.com/en/US/products/hw/phones/ps379/products_qanda_item09186a00808996f3.shtml. 

^ "3Com, Power over Ethernet, Current State of the Technology and the IEEE Standard". http://www.at2.com/downloads/documents/3com/power_over_ethernet_wp.pdf.  080803 at2.com

^ National Semiconductor application note 1474: "The LM507X Family of PoE Devices: Frequently Asked Questions (FAQs)"

External links

ieee802.org: Download the IEEE 802.3 standards

ieee802.org: IEEE 802.3af Task Force

ieee802.org: IEEE 802.3at Task Force

www.altair.org Power Over Ethernet

PoE portal

Categories: Ethernet | Networking hardware | Wireless networking | Remote controlHidden categories: Articles to be expanded from October 2009 | All articles to be expanded | All articles with unsourced statements | Articles with unsourced statements from March 2007
About the Author

I am an expert from China Manufacturers, usually analyzes all kind of industries situation, such as 8mm video camera , mifare card.

Cisco Industrial Ethernet 3000 Series Switch. Each $1394.7 Manufacturer: Cisco Systems, Inc. Each. The Cisco Industrial Ethernet 3000 (IE 3000) Series Switches are a new family of switches that provide a rugged, easy-to-use, secure switching infrastructure for harsh environments. The Cisco IE 3000 family features

CP TECH Level One IFE-0502 Industrial Fast Ethernet Switch $235.99 1 Gbps 1 x SC 100Base-FX 1.5 Mpps 10/100Base-TX 100Base-FX 4 x RJ-45 10/100Base-TX PoE LAN 48 V DC 5 5.51" Height x 1.18" Width x 3.74" Depth Level One IFE-0502 Industrial Fast Ethernet Switch DIN rail kit Wall-mount ear Wavelength: 1310nm Distance: 30km The LevelOne IFE-0501 and IFE-0502 4-Port 10/100TX PoE and 1-port 100 SC Fiber Industrial Fast Ethernet Switches combine PoE capability and 4-port switching into a small heavy-duty metal casing for Industrial PoE applications. The IEEE802.3af Power over Ethernet compliant switches connect to a 48V DC power source to provide power and 10/100Mbps data transmission over Ethernet cabling to attached devices. AC Adapter CP TECH CP Technologies Ethernet Switch IFE-0502 Level One IFE-0502 Industrial Fast Ethernet Switch Wall-mountable Yes www.cptechusa.com

Transition Networks Industrial Managed Ethernet Switch with PoE $947.99 (2 Total) SFP Shared 1 x RJ-45 RS-232 Console Management 10 10/100/1000Base-T 10/100Base-TX 2 2 x RJ-45 10/100/1000Base-T LAN 32 MB 4 MB 48 V DC 5.60 Gbps 6" Height x 2.83" Width x 4.13" Depth 8 x RJ-45 10/100Base-TX LAN 8.3 Mpps IEEE 802.1Q (VLAN Tagging) IEEE 802.1p QoS SNMP v1 v2c, v3 Web Telnet CLI Transition Networks Industrial Switches are hardened devices designed to reliably operate in harsh environments such as those found on factory floors, outdoor enclosures or other hazardous environments. DRAM Ethernet Switch Industrial Managed Ethernet Switch with PoE Lifetime Power Supply SISPM1040-182D-LRT Transition Networks Transition Networks, Inc Wall-mountable Yes www.transition.com

CP TECH LevelOne IFE-0501 Industrial Fast Ethernet Switch $215.99 1 Gbps 1 x SC 100Base-FX LAN 10/100Base-TX 100Base-FX 149 Kpps 2 4 x RJ-45 10/100Base-TX PoE LAN 5 DIN-Rail installation option The LevelOne IFE-0501 and IFE-0502 4-Port 10/100TX PoE and 1-port 100 SC Fiber Industrial Fast Ethernet Switches combine PoE capability and 4-port switching into a small heavy-duty metal casing for Industrial PoE applications. The IEEE802.3af Power over Ethernet compliant switches connect to a 48V DC power source to provide power and 10/100Mbps data transmission over Ethernet cabling to attached devices. The IFE-0501 and IFE-0502 Industrial PoE Switch is designed for network devices operating in harsh environments. The ports and PoE injector are enclosed in a robust and durable metal casing. The switches are easily installed at network edges where AC power is not always available. The switches are built to operate between -10°C and 60°C in 95% non-condensing humidity and are suitable for covered outdoor installation. Mounting options include wall-mounting, DIN-rail mounting and stand-alone panel mounting. AC Adapter CP TECH CP Technologies Ethernet Switch IFE-0501 LevelOne IFE-0501 Industrial Fast Ethernet Switch Wall-mountable Yes www.cptechusa.com

ALLIED TELESIS INC. ATGS900/1610 UNMANAGED SWITCHES $283.87 The Allied Telesis ATGS900 series of unmanaged Gigabit switches are designed for medium enterprises and education networks. The ATGS900 series were built to deliver high bandwidth applications such as video graphics or industrial design to the end user with the high speed and high performance that only Gigabit can provide.Primary InformationForm Factornbsp;:nbsp;nbsp;Externalnbsp;Networking Typenbsp;:nbsp;nbsp;Switchnbsp;Data Transfer Ratenbsp;:nbsp;nbsp;1 Gbpsnbsp;Networking / Ports Qtynbsp;:nbsp;nbsp;16nbsp;Data Link Protocolnbsp;:nbsp;nbsp;Ethernetnbsp;Connectivity Technologynbsp;:nbsp;nbsp;Wirednbsp;Communication Modenbsp;:nbsp;nbsp;Fullduplex; Halfduplexnbsp;Data Link Protocolnbsp;:nbsp;nbsp;Fast Ethernet; Gigabit Ethernetnbsp;Voltage Requirednbsp;:nbsp;nbsp;AC 120/230 V ( 50/60 Hz )nbsp;Featuresnbsp;:nbsp;nbsp;Flow control autonegotiation autouplink (auto MDI/MDIX)nbsp;DimensionsMiscellaneousWidthnbsp;:nbsp;nbsp;13 Inchnbsp;Depthnbsp;:nbsp;nbsp;9.1 Inchnbsp;Heightnbsp;:nbsp;nbsp;1.7 Inchnbsp;SystemInterfacesnbsp;:nbsp;nbsp;16 x network Ethernet 10BaseT/100BaseTX/1000BaseTX RJ45nbsp;ServiceSupportService Support Typenbsp;:nbsp;nbsp;Limited lifetime warrantynbsp;UNSPSC CodeUNSPSC Codenbsp;:nbsp;nbsp;43222612nbsp;

Cisco Gigabit Ethernet SFP $2754.99 1 1 Gbps 1 Gbps Gigabit Ethernet 1 x 1000Base-ZX 1 x LC 1000Base-ZX 1000Base-ZX 90 Spare Product Optical Range: 40km Cisco Industrial Ethernet 3000 Series Switches Cisco Cisco Systems, Inc Data Networking GLC-ZX-SM-RGD= Gigabit Ethernet SFP SFP (mini-GBIC) Single-mode Fiber 1000Base-ZX www.cisco.com

Industrial Ethernet Serial Server device server $215.99 Black Box Industrial Ethernet Serial Server - Device server - Ethernet Fast Ethernet RS-232 RS-422 RS-485

Allied Telesyn 1 Port Unpopulated GBIC Module for 8024M 8016F 8088 & 8012M Ethernet Switches ATA47 $67.8 Allied Telesyn 1 Port Unpopulated GBIC Module for 8024M 8016F 8088 & 8012M Ethernet Switches ATA47

D-Link L2+ Unified Wired/Wireless Gigabit PoE Switches - Manageable - Power Over Ethernet DWS316024TC $1335.61 D-Link L2+ Unified Wired/Wireless Gigabit PoE Switches - Manageable - Power Over Ethernet DWS316024TC

D-Link L2+ Unified Wired/Wireless Gigabit PoE Switches - Manageable - Power Over Ethernet DWS316024PC $2428.71 D-Link L2+ Unified Wired/Wireless Gigabit PoE Switches - Manageable - Power Over Ethernet DWS316024PC

Cisco 3000-8TC Industrial Ethernet Switch $1261.99 (2 Total) SFP (mini-GBIC) Uplink (4 Total) Expansion Slot 1 Year Limited 10 10/100Base-TX 128 MB 2 3000 3000-8TC 3000-8TC Industrial Ethernet Switch 4.40 lb 5.80" Height x 6" Width x 4.40" Depth 6 64 MB 8 x RJ-45 10/100Base-TX LAN DHCP Telnet RMON SNMP v1, v2, v3 IEEE 802.1p QoS IEEE 802.1Q VLAN Web-based Management 2 dual-purpose uplinks (each dual-purpose uplink port has one 10/100/1000 Ethernet port and one SFP-based Gigabit Ethernet port, one port active) The Cisco Industrial Ethernet 3000-8TC Switch is a new switch that provides a rugged, easy-to-use, secure switching infrastructure for harsh environments. The Cisco IE 3000-8TC features industrial design and compliance; tools for ease of deployment, management, and replacement; and network security based on open standards. The Cisco IE 3000-8TC is an ideal product for Industrial Ethernet applications, including factory automation, intelligent transportation systems (ITSs), substations, and other deployments in harsh environments. Cisco Cisco Systems, Inc DRAM Ethernet Switch IE-3000-8TC Power Supply Rack-mountable Yes www.cisco.com

Cisco 3000-4TC Industrial Ethernet Switch $951.99 (2 Total) SFP (mini-GBIC) Shared (4 Total) Expansion Slot 1 Year Limited 10/100/1000Base-T 10/100Base-TX 128 MB 2 2 x RJ-45 10/100/1000Base-T LAN 3000 3000-4TC 3000-4TC Industrial Ethernet Switch 4 x RJ-45 10/100Base-TX LAN 4.40 lb 5.80" Height x 6" Width x 4.40" Depth 6 64 MB DHCP Telnet RMON SNMP v1, v2, v3 IEEE 802.1p QoS IEEE 802.1Q VLAN Web-based Management Shock/vibration Surge ratings Complete set of power input options Convection cooling DIN-rail or 19" rack mounting The Cisco Industrial Ethernet 3000-4TC Switch is a new switch that provides a rugged, easy-to-use, secure switching infrastructure for harsh environments. The Cisco IE 3000-4TC features industrial design and compliance; tools for ease of deployment, management, and replacement; and network security based on open standards. The Cisco IE 3000-4TC is an ideal product for Industrial Ethernet applications, including factory automation, intelligent transportation systems (ITSs), substations, and other deployments in harsh environments. Cisco Cisco Systems, Inc DRAM Ethernet Switch IE-3000-4TC Power Supply Rack-mountable Yes www.cisco.com

XBlue Industrial Managed All-Gigabit Power-over-Ethernet (PoE) Plus - Switch - 8 Ports - Managed - DIN Rail Mountable, Wall-mountable. Each $1389.23 Manufacturer: Transition Networks, Inc. Each. Transition's Industrial PoE+ switches are Power Sourcing Equipment (PSE) devices that are designed to comply with the IEEE802.3at 2009 and IEEE802.3af 2003 standards and combine data received over a fiber opti

Startech.com / StarTech.com 5 Port Unmanaged Industrial Ethernet Switch / IES5100 $100.2 Startech.com - StarTech.com 5 Port Unmanaged Industrial Ethernet Switch - IES5100

Cisco Industrial Ethernet Switch 4xEXPANSION Slot 2xSFP 4x10/100BASE-TX 2x10/100/1000BASE-T IE30004TC $1038 Cisco Industrial Ethernet Switch 4xEXPANSION Slot 2xSFP 4x10/100BASE-TX 2x10/100/1000BASE-T IE30004TC

Fluke DTX-1800-IE 120 Cable Analyzer for Industrial Ethernet DTX1800IE120 $10431.93 Fluke DTX-1800-IE 120 Cable Analyzer for Industrial Ethernet DTX1800IE120

Cisco 3000-8TC Industrial Ethernet Switch 8-Ports IE30008TC IE-3000-8TC $1395.57 Cisco 3000-8TC Industrial Ethernet Switch 8-Ports IE30008TC IE-3000-8TC

Industrial Evdo Verizon Cellular Vpn Router Including Ethernet And Rs-232/422/48 $702.99 INDUSTRIAL EVDO VERIZON CELLULAR VPN ROUTER INCLUDING ETHERNET AND RS-232/422/48

Cisco Industrial Ethernet Switch With (8) Ethernet 10/100-Ports (2) Dual-purpose Uplink Ports IE30008TC $923.42 Cisco Industrial Ethernet Switch With (8) Ethernet 10/100-Ports (2) Dual-purpose Uplink Ports IE30008TC

Ife-0502 - Level One Ife-0502 4-Port 10/100 W/1-Port Sc Single Mode Poe Industrial Switch - 4 X 10/100Base-Tx $256.89 the Levelone Ife-0501 And Ife-0502 4-port 10/100tx Poe And 1-port 100 SC Fiber Industrial Fast Ethernet Switches Combine Poe Capability And 4-port Switching Into a Small Heavy-duty Metal Casing For Industrial Poe Applications. The Ieee802.3af Power Over Ethernet Compliant Switches Connect to a 48v DC Power Source to Provide Power And 10/100mbps Data Transmission Over Ethernet Cabling to Attached Devices. [IFE0502] UPC: 878742003616 UNSPC: 43222612 8.5L x 6.5W x 2.75H 1.65 LB

Sistf1010-280-Lrt - Transition Networks Sistf1010-280-Lrt Industrial Ethernet Switch - 8 Port - 8 X 10/100Base-Tx $258.7 transition's Industrial Switches With Class 1 Div 2 Certification Are Hardened Devices Designed to Reliably Operate in Harsh Environments Such as Those Found on Factory Floors, Outdoor Enclosures, Oil And Gas Refining, Chemical Plants or Other Hazardous Environments. [CE7467] UPC: 648177027897 UNSPC: 43222612 2L x 4W x 2H 2 LB 0.09 Cubes

Cisco Catalyst 2955T12 Ethernet Switch 12 x 10100BaseTX Ethernet Switch WSC2955T12 $1619.08 Cisco Catalyst 2955T12 switch is industrialgrade switching product that provide wirespeed Fast Ethernet and Gigabit Ethernet connectivity for deployment in harsh environments. The Cisco Catalyst 2955T12 operates in environments such as industrial networking solutions (industrial Ethernet deployments) intelligent transportation systems (ITS) and transportation network solutions. It integrates into military equipment Supervisory Control and Data Acquisition (SCADA) systems power generation systems waste water treatment facilities building automation systems warehouses and any other facilities or applications where the environmental conditions or suspended solid concentrations exceed the specifications of other commercial switching products. The Cisco Catalyst 2955T12 uses industrialgrade components a compact form factor convection cooling and relay output signaling to extend intelligent services such as enhanced security high availability and advanced quality of service (QoS) to areas that cannot be served by traditional commercialgrade Ethernet switches.

Sispm1040-182D-Lrt - Transition Networks Industrial Managed Ethernet Switch With Poe - 2 X Sfp Shared - 8 X 10/100Base-Tx Lan, 2 X 10/100/1000Base-T Lan $990.06 transition Networks Industrial Switches Are Hardened Devices Designed to Reliably Operate in Harsh Environments Such as Those Found on Factory Floors, Outdoor Enclosures or Other Hazardous Environments. [V01857] UPC: 648177025770 UNSPC: 43222612 3L x 1W x 2H 1 LB

Transition Networks SISTF1010-180 Ethernet Switch - 8 Port $345.99 1.2 Mpps 1.41 lb 1.60 Gbps 10/100Base-TX 12 V DC to 48 V DC 2 5.30" Height x 2.10" Width x 4.10" Depth 8 8 x RJ-45 10/100Base-TX Network LAN SISTF1010-180 Unmanaged Ethernet Switch 1 x DIN-Rail mounting bracket (installed) 1 x Wall mount plate 6 x Screws (for attaching wall-mount bracket) 1 x Installation manual CD 1 x Barrel connector interface cable The SISTF1010-180-LR(T) Industrial Unmanaged Switch provides eight 10/100Base-TX (RJ-45) copper connections. These switches are hardened devices designed to reliably operate in harsh environments such as those found on factory floors, outdoor enclosures or other hazardous environments. AC Adapter Ethernet Switch Lifetime Limited No SISTF1010-180 SISTF1010-180 Unmanaged Ethernet Switch SISTF1010-180-LRT Transition Networks Transition Networks, Inc WEEE Wall-mountable Yes www.transition.com

Transition Networks SISTF1010-250-LRT Ethernet Switch - 5 Port $223.99 1 Gbps 10/100Base-TX 12 V DC 12 V DC to 48 V DC 149 Kpps 2 5 5 x RJ-45 10/100Base-TX Network LAN 5.51" Height x 1.18" Width x 3.74" Depth SISTF1010-250-LRT Class 1 Div 2 Industrial Switch DIN Rail Mounting Brackets Wall Mount Brackets Barrel connector interface cable Transition's Industrial Switches with Class 1 Div 2 Certification are hardened devices designed to reliably operate in harsh environments such as those found on factory floors, outdoor enclosures, oil and gas refining, chemical plants or other hazardous environments. AC Adapter Ethernet Switch Lifetime SISTF1010-250-LRT SISTF1010-250-LRT Class 1 Div 2 Industrial Switch Transition Networks Transition Networks, Inc Wall-mountable Yes www.transition.com

StarTech.com 5 Port Unmanaged Industrial Ethernet Switch $83.99 1 Year Limited 10/100Base-TX 12 V DC to 48 V DC 148 Kpps 2 4.33" Height x 1.02" Width x 2.76" Depth 5 5 Port Unmanaged Industrial Ethernet Switch 5 x RJ-45 10/100Base-TX Network LAN 7.06 oz Industrial Unmanaged Ethernet Switch Instruction Manual Power Adapter Supports 2048 Mac addresses Din-Rail Mountable This 5 port (unmanaged) Industrial Ethernet Switch is designed to operate in harsh environments, making it an ideal solution for factory floors, warehouses, and outdoor locations without temperature control. The Ethernet switch can be DIN rail mounted and features compact, hardened construction that can be installed in any environment, able to operate within extended temperature ranges from -10°C to 60°C This versatile switch features 10/100Mbps and full/half-duplex auto-negotiation and auto MDI/MDIX operation. Ethernet Switch IES5100 No Power Supply RoHS StarTech.com Yes www.startech.com

Transition Networks Fast Ethernet Media Converter $464.99 1 x ST 1.24 Mile 10/100Base-TX 100Base-FX 4 x RJ-45 5 5.50" Height x 1.20" Width x 3.70" Depth Fast Ethernet Media Converter DIN Rail Mounting Kit Wall Mount Brackets Wavelength: 1300nm POE to Remotely Located Devices in Harsh Filtering Addresses: 1K MAC Addresses Back Plane: 1.0 Gbps Auto-Negotiation for 10/100BASE-TX Dry Contact Relay Alarm Output Dual, Redundant 48V DC Power Inputs Reverse Polarity Power Input Protection Overload Current Protection Transition's Industrial POE switches are Power Sourcing Equipment (PSE) devices that are comply with the IEEE802.3af 2003 standard and combine data received over a fiber optic link with -48VDC power; providing power to Powered Devices (PD) over unshielded twisted pair cabling. These Industrial POE Switches are hardened devices designed to reliably operate in harsh environments such as those found on factory floors, outdoor enclosures or other hazardous environments while providing all the benefits of POE power. External Fast Ethernet Media Converter Lifetime Media Converter SISTP1011-141-LRT Transition Networks Transition Networks, Inc www.transition.com

Sisgm1040-244-Lrt - Transition Networks Sisgm1040-244-Lrt Industrial Ethernet Switch - 4 Port - 4 Slot - 4 X 10/100/1000Base-T - 4 X Sfp (Mini-Gbic) Slot $884.6 transition's Industrial Managed Switches With Class 1 Div 2 Certification Are Hardened Devices Designed to Reliably Operate in Harsh Environments Such as Those Found on Factory Floors, Outdoor Enclosures, Oil And Gas Refining, Chemical Plants or Other Hazardous Environments. Full Management Features Include Support For Redundant Rings,vlans, Igmp, Snmp, Web, Telnet, And Cli. [CE7471] UPC: 648177027804 UNSPC: 43222612 2L x 4W x 2H 4 LB

Comtrol RocketLinx ES8108F Fast Ethernet Industrial Switch $361.99 1.5 Mpps 10 10/100Base-FX 100Base-FX 12 V DC to 48 V DC 2 2 Gbps 2 x SC Duplex 100Base-FX 24 V DC 32057-9 5 Year Limited 8 x RJ-45 10/100Base-FX LAN Multi-Mode Broadcast Traffic Threshold: 200 packets/sec Aluminum case with IP-31 grade protection QoS The RocketLinx ES8108F is Comtrol's 8-port Fast Ethernet industrial switch featuring a 2.0Gbps Packet Switch engine and packet forwarding and filtering mechanisms to meet industrial communications standards. It provides packet forwarding capabilities to handle 64-1552 packet sizes in two priority queues to optimize data forwarding performance. Additionally, for the best network performance, both broadcast storm filtering and fl ow control functions ensure data delivery free of traffic congestion. AC Adapter Comtrol Comtrol Corporation ES8108F Ethernet Switch RoHS RocketLinx RocketLinx ES8108F Fast Ethernet Industrial Switch Wall-mountable Yes www.comtrol.com

Industrial Ethernet 3010 Series - switch - 24 ports - managed - rack-mountable $3439.99 Cisco Industrial Ethernet 3010 Series - Switch - L2+ - managed - 24 x 10/100 + 2 x combo Gigabit SFP - rack-mountable

IMC IE-MiniMc Industrial Ethernet Media Converter $166.99 0.83" Height x 0.83" Width x 3.35" Depth 1 x RJ-45 1 x ST Duplex 1.24 Mile 10/100Base-TX 10/100Base-TX UTP 100Base-FX 100Base-FX 50/125 µm Multi-mode Fiber 100Base-FX 62.5/125 µm Multi-mode Fiber 2 55-19722 6 Year IE-MiniMc Industrial Ethernet Media Converter AC power adapter DIN-35 rail The IE-MiniMc 55-19722 provides a conversion between 10/100 UTP and 100Base-FX multi-mode fiber. IE-MiniMc 55-19722 allows operation in extreme temperatures, and offers several power and mounting options. External Fiber IE-MiniMc Industrial Ethernet Media Converter IMC IMC Networks Corp. Media Converter MiniMc Rack-mountable UTP Wall-mountable www.imcnetworks.com

Industrial Ethernet Serial Server - Device server - Ethernet Fast Ethernet RS-232 RS-422 RS-485 (Open Box Product Limited Availability No Back Orders) $94.74 Whether serial devices are on the factory floor or in a remote location you can now control them across your Ethernet network with BLACK BOX Industrial Ethernet Serial Server

Ethernet Networks $120 Ethernet Networks, Fourth Edition, provides everything you need to know to plan, implement, manage and upgrade Ethernet networks. * Improve your skills in employing Ethernet hubs, switches, and routers. * Learn how to set up and operate a wireless Local Area Network (LAN). * Discover how to extend a wired Ethernet via wireless LANs. * Understand cabling standards and the role of NEXT (Near End Crosstalk), FEXT (Far End Crosstalk) and other transmission parameters. * Profit from Gilbert Held's tips and tricks on enhancing security ... and much more. This indispensable resource features up-to-date coverage of: * Wireless Ethernet (IEEE802.11 standards) * 10Gbps Ethernet * Firewalls in both a wired and wireless environment * The operation of new versions of Windows(r) on Ethernet LANs * The use of LAN switches at and above layer 2 in the ISO reference model * Copper and fiber optic cable to transport high speed Ethernet Network planners, administrators, and system engineers working with Ethernet networks will find Ethernet Networks, Fourth Edition, an invaluable tool for implementing, updating, and managing their networks.

Transition Networks Fast Ethernet Industrial Converter Switch $973.99 1.24 Mile 10/100Base-TX 10/100Base-TX UTP 100Base-FX 100Base-FX 1300 nm Multi-mode Fiber 2 x ST Duplex 5.30" Height x 2.10" Width x 4.10" Depth 6 x RJ-45 8 Fast Ethernet Industrial Converter Switch Barrel connecter interface cable It operates at standard operating temperature: (0°C to 60°C) SNMP trap and SMTP email trap support SNTP Clock Synchronization Bandwidth Allocation Dry Contact Relays Transition Network's Industrial Converter Switch is hardened device designed to reliably operate in harsh environments such as those found on factory floors, outdoor enclosures or other hazardous environments. The Converter switch can connect to either 10Base-T or 100Base-TX ports and can provide redundant 100Base-FX fiber optic connections for links up to 2km. Fast Ethernet Industrial Converter Switch Fiber Lifetime Media Converter SISTM1011-162-LR Transition Networks Transition Networks, Inc UTP www.transition.com

Tacony Tacsew Assembled Table, Stand, 1/2HP CLUTCH Motor110V 220V & Reverse Switches for Industrial Sewing Machine HEAD: Specify Brand, Model, RPM, HP $299 Clutch Motors have switches to change input voltage from 110V to 220V, and a switch for reversing the motor to clockwise or counterclockwise direction for handwheel rotationTacony Tacsew Assembled Table, Stand, 1/2HP CLUTCH Motor110V 220V & Reverse Switches for Industrial Sewing Machine HEAD: Specify Brand, Model, RPM, HP

This entry was posted on Sunday, July 1st, 2007 at 10:23 pm and is filed under Uncategorized. You can follow any responses to this entry through the RSS 2.0 feed. You can leave a response, or trackback from your own site.