Ide Raid Controller
 |
US $10.99
Approach data recovery experts immediately if RAID 0 fails
RAID refers to an architecture whereby a large number of inexpensive disks are grouped together to form a single high storage system which offers superior performance in terms of capacity and reliability. Redundancy is a major factor in a RAID array which allows a form of data backup in event of failure. RAID 0, is however, not a valid type of RAID as it doesn't offer any level of redundancy and thus, if one drive fails, the data gets damaged. In such unfortunate cases, a regular backup can come to your rescue. But if you are not able to recover required data from a failed RAID 0 array, you still have a hope in data recovery services.
Understanding RAID 0 failure
A disk failure in RAID 0 can amount to severe data loss as it uses 'striping' technique to write data. Through stripping, data is broken into fragments while it gets written to the drive. The fragments are then written to their respective disks simultaneously on the same sector. During the read process, the data is read off the drive in parallel and so, this type of arrangement delivers huge bandwidth.
The disadvantage of using a RAID 0 array is that a single drive failure can destroy the entire architecture which is not fault tolerant in this case. Moreover, RAID 0 doesn't even have the provision of error checking.
Factors responsible for RAID 0 failure
A RAID 0 architecture can succumb to any of the following circumstances and in order to recover data, one has to completely rely on companies providing data recovery services. Let's have a look at some of the circumstances which can lead to RAID 0 failure
-
RAID controller failure
-
Natural disaster (fire or water damage)
-
Volume reconstruction problem or RAID rebuilt error
-
Power spikes and outages
-
Virus attacks and many others
Preventive steps to be taken
If and when you witness a RAID 0 failure, do not attempt to rebuilt yourself as you may end up marring the chances of data recovery. As precautionary measures you can undertake the following steps:
-
Turn off the system without any further delay
-
Refrain from using any disk repair utility
-
Do not run any volume repair utility
-
Contact data recovery experts immediately
Stellar Data Recovery Inc., an Edison based company, is a leading name when it comes to acquiring safe, reliable and cost-effective data recovery New Jersey. RAID recovery, in case of physically damaged hard drives, is performed in Class 100 Clean Rooms by highly-trained RAID engineers. Stellar provides data recovery NJ for different RAID levels (RAID 0, RAID 1, RAID 2, RAID 6) and hard drive makes (SATA, IDE, EIDE, SCSI etc).
About the Author
Andrew Watson has 6 Years of Experience in the Software Technology field doing research in Stellar Data Recovery Inc. which offers data recovery, data recovery services, hard drive recovery services and data recovery New Jersey.
|
|
Promise Controller IDE PCI FAST-TRAK66 RAID FASTTRACK66 $16 Promise Controller IDE PCI FAST-TRAK66 RAID FASTTRACK66 |
|
|
3ware IDE RAID 4CH PCI Controller 7506-12R Storage Controller $134.18 3ware IDE RAID 4CH PCI Controller 7506-12R Storage Controller |
|
|
Pci Host Controller Card 100/133 Silicon Ide Raid Pci Host $23.99 PCI HOST CONTROLLER CARD 100/133 SILICON IDE RAID PCI HOST |
|
|
3ware Escalade 8500-12 RAID ATA133/100 IDE PCI 64bit 850012 8500-12 8500-12KIT Storage Controller (RAID) $120.3 3ware Escalade 8500-12 RAID ATA133/100 IDE PCI 64bit 850012 8500-12 8500-12KIT Storage Controller (RAID) |
|
|
3ware Escalade 7500-4LP RAID DMA/ATA-133 IDE PCI 7500-4LP Storage Controller (RAID) Plug-in Card $18.51 3ware Escalade 7500-4LP RAID DMA/ATA-133 IDE PCI 7500-4LP Storage Controller (RAID) Plug-in Card |
|
|
3ware Escalade 7506 RAID ATA-133 IDE PCI 6CH 7506-12 Storage Controller (RAID) Plug-in Card $268.34 3ware Escalade 7506 RAID ATA-133 IDE PCI 6CH 7506-12 Storage Controller (RAID) Plug-in Card |
|
|
Promise FASTTRAK100TX2 FastTrak IDE RAID ATA-100 Controller $45.72 This dual-channel RAID card offers powerful options for small office/home office and professional workstations at incredible values. Creates economical fault-tolerant RAID 1 arrays for entry-level networks.Interface type: PCIController interface type: ATA-100Data transfer rate: 100 MBpsSupported devices: Hard drive, CD drive, DVD drive, disk array (RAID)Channel quantity: 2Maximum storage devices quantity: 4RAID level: RAID 0, RAID 1Interfaces: 2 x storage - ATA-100 - 40 pin IDC ( internal )Model: FASTTRAK100TX2Dimensions: 3.1 inches wide x 0.5 inches deep x 4.5 inches highIncluded items: IDE Controller, softwareWeight: 1.5 pounds |
|
|
2S1I PCI SATA IDE Combo Controller Adapter Card - storage controller (RAID) - ATA-133 / SATA-150 - PCI / 66 MHz $32.99 StarTech.com 2S1I PCI SATA IDE Combo Controller Adapter Card - Storage controller (RAID) - 3 Channel - ATA-133 / SATA-150 - 150 MBps - RAID 0 1 JBOD - PCI / 66 MHz |
|
|
2S2I PCI Express SATA IDE Combo Controller Adapter Card - storage controller (RAID) - ATA-133 / SATA-300 / eSATA-300 - PCIe $38.99 StarTech.com 2S2I PCI Express SATA IDE Combo Controller Adapter Card - Storage controller (RAID) - ATA-133 / SATA-300 / eSATA-300 - 300 MBps - RAID 0 1 JBOD - PCIe |
|
|
PCI Ultra ATA 133/100 IDE RAID Controller Card $15.6 Ultra ATA133 IDE RAID PCI Controller Card Supports sofware Raid 0, 1 or 0 +1 (optional) Supports IDE bus Ultra DMA at ATA 133/100Mbytes/sec PCI burst rate Supports maximum PCI bus master data transfer rate of 266MB/sec. Two independent Ultra ATA channels with 128 Bytes buffer per channel Supports up to four IDE/ATA devices (coexists with other IDE and SCSI controllers) Fully backwards compatible with Ultra ATA/33, EIDE/Fast ATA-2 IDE And ATAPI devices Supports Ultra DMA2, 3, 4 ; Multi-Word DMA0, 1, 2 And PIO 2, 3, 4 driver modes Compliant to ATA/ATAPI-5 specification and PCI specification version 2.1. Enhanced data integrity of transferred data with CRC (cyclical redundancy check) protection and verification Compatible with Microsoft IDE/ATA drives Most Ideal for attaching extra hard disks to your system Optical drives or other type of the drives may not work You should connect optical drives to onboard IDE controller |
|
|
Cables Unlimited ATA IDE PCI Raid Controller Card $29.99 0 0+1 1 1 Year 2 2 x 40-pin IDC Ultra ATA/133 (ATA-7) - ATA Adjustable stripe size for RAID 0 and 0+1 Automatic performance tuning for each device attached Allows HDDs with different sizes to be configured in a RAID set ATA/ATAPI-6, UDMA6 ATA/133 compliant Fully backwards compatible with Ultra ATA/100, Ultra ATA/66, Ultra ATA/33, EIDE/Fast ATA-2, IDE and ATAPI devices Dual Channel Ultra ATA 133 IDE RAID Controller 1 x Cable User's manual Software driver 1 x Utility disc Windows 98SE Windows Me Windows 2000 Windows XP Windows NT 4.0 Windows DOS Protect your valuable data and increase system performance with this dual-channel Ultra ATA 133 IDE RAID Controller. Supporting multiple levels of RAID protection, this card is a must for all PCs. Use RAID 1 to create a fault tolerant, economical system where if one drive fails, your data is still safe on the other. Write data across multi drives to improve data transfer rates with RAID 0. ATA IDE PCI Raid Controller Card ATA RAID Controller Cables Unlimited IOC-8000 PC PCI Plug-in Card Ultra ATA/133 (ATA-7) Up to 133 MBps Up to 4 x Physical www.cablesunlimited.com |
|
|
4 Port PCI Combo SATA RAID + IDE ATA Controller Card $12.8 Power by VIA 6421 Chip - SATA RAID + ATA133/100 Internal Interface 2 x Serial ATA 150 + 1 x ATA 133 External Interface 1 X SATA 150 3 Ports SATA supports RAID 1/0 0+1, and PIO mode 4/3/2/1/0 Support 24 bit hard disk mode >147MB (Please check with Microsoft website for enable 24 bit Mode) Support IDE bus Ultra DMA at ATA 133/100Mbytes/sec PCI burst rate Support maximum PCI bus master data transfer rate of 133MB/sec. PCI interrupt sharing and coexists with main board IDE controller 100% Plug and Play |
|
|
SYBA PCI to SATA/ IDE Combo RAID Controller Card SY-VIA-150R $39.48 This is a SYBA PCI to SATA/ IDE (2 SATA/ 2 PATA) combo RAID controller card. Upgrade your system by expanding your computer's connectivity with this card.Supports two SATA and two PATA hard drivesOnly SATA supports RAIDSupports ATA 133 high performance hard disk drivesSupports hard disk drives larger than 137 GB (48-bits LBA)Supports Ultra DMA mode 6/ 5/ 4/ 3/ 2/ 1/ 0, DMA mode 2/ 1/ 0, and PIO mode 4/ 3/ 2/ 1/ 0Supports PCI Plug and Play. PCI interrupt sharing and coexists with main board IDE controllerSupports IDE bus master operationSupports RAID 0/ 1/ 0+1 and JBOD4 KB to 64 KB striping block size supportBootable disk or disk array supportWindows-based RAID configure and management software toolSupports hot-swap failed disk drive in RAID 1 arrayMirroring automatic background rebuilds supportATA SMART function supportSupports Windows 98/ ME/ NT 4.0/ 2000/ XPPart number: SYBA SY-VIA-150RWarning: California residents only, please note per Proposition 65, this product may contain one or more chemicals known to the State of California to cause cancer, birth defects, and/or other reproductive harm. Wash hands after handling or using this product, and contact the manufacturer(s) for information regarding the chemicals that may be contained in these products. |
|
|
SYBA PCI to SATA/ IDE PCRDSATACON7 Combo RAID Controller Card $18.09 Upgrade your system by expanding it with two extra internal Serial ATA (SATA) ports and one internal Parallel ATA port. This controller card is a great way to optimize your computer's performance.Supports two SATA and two PATA hard drivesOnly SATA supports RAIDSupports ATA 133 high performance hard disk drivesSupports hard disk drives larger than 137 GB (48-bits LBA)Supports Ultra DMA mode 6/5/4/3/2/1/0, DMA mode 2/1/0, and PIO mode 4/3/2/1/0Supports PCI plug-and-playSupports Windows 98 / ME / NT 4.0 / 2000 / XPPCI interrupt sharing and coexists with main board IDE controllerSupports IDE bus master operationSupports RAID 0 / 1 / 0+1 and JBOD4 KB to 64 KB striping block size supportBootable disk or disk array supportWindows-based RAID configure and management software toolSupports hot-swap failed disk drive in RAID 1 arrayMirroring automatic background rebuilds supportATA SMART function supportModel number: PCRDSATACON7Package includesPCI SATA / IDE combo controller cardSATA cableDriver CDUser manualWarning: California residents only, please note per Proposition 65 that this product may contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. |
|
|
ACARD AEC6885M PCI 4 Channel IDE RAID Adapter for Mac $236.93 AEC6885M is a 64bit/66MHz PCItoIDE controller for Macintosh with transfer rate reaching 533MB/s. It has 4 independent IDE channels and supports true hardware RAID 0 1 0+1 and normal mode. The 48bit LBA (Logical Block Addressing) technology makes it good for big hard drive over 137GB. RAID Utility provides you a GUI tool to easily manage the RAID subsystem. AEC6885M fully supports 64bit PCI specifications including Bus Master to increase transfer capability and also supports Scatter/Gather to enhance multitasking effects. The highly effective AEC6885M is fit for Macintosh workstations and servers. It can meet your need in storage and data protection. Features. PCItoIDE RAID controller 4 independent IDE channels < 64bit/66MHz True Mac OS X support Supports Ultra ATA133/100 HDD Supports big HDD (exceeding 137GB). Specifications. Data I/O Mode: 64bit PCI Bus Master Supports big HDD (exceeding 137GB) Data transfer rate up to 533 MB/s DIP switch setting for RAID configuration and normal mode Connects up to 4 IDE hard drives Supports four IDE 40pin connectors Supports firmware update Coexists with onboard IDE controller RAID Functions. Supports RAID 0 1 0+1 and Normal. Supports booting from RAID Volume and Normal mode. IDE BUS. 4 independent IDE channels. Supports Ultra DMA 133 and transfer rate reaches 133MB/s. Uses 48bit LBA technology to support high capacity hard drives. Strongly recommended to use ATA 66/100/133 IDE cable for best performance. PCI BUS. Compliance with PCI 2.2 specifications. Data transfer rate up to 533 MB/sec. Supports Scatter/Gather function. Low command overhead. Supports multitasking and multithreaded processing. PCI Plug and Play. O.S Compatibility. Mac OS 9 Mac OS X 10.2.x (nonbootable) Mac OS X 10.3 Mac OS X 10.4. |
|
|
ACARD AEC6880M PCI Ultra ATA 133 RAID IDE Adapter for Mac $159.71 AEC6880M is a highperformance dualchannel PCI PnP Ultra ATA133 RAID adapter. It supports true Hardware RAID 0 1. The easeofuse RAID utility helps quickly create and manage RAID subsystem. The 48bit LBA (Logical Block Addressing) technology makes it good for big hard drive over 137GB.Features. Supports true Mac OS X A standalone PCItoIDE RAID controller In normal mode as IDE device extension The same firmware for OS 8.5 OS 9 and OS X Supports HDD larger than 137GB. RAID Functions. Supports true Hardware RAID 1 (Mirroring) RAID 0 (Striping) Capable of booting from standard and RAID volume. Specifications. DIP Switch setting for RAID 0 mode RAID 1 mode or normal mode Coexist with onboard IDE controller Open Firmware interface Max. 4 IDE devices. IDE Bus Dual independent channels of IDE bus Supports Ultra ATA133/100/66/33 hard disk Supports 48bit addressing with Big Drive technology Data transfer rate up to 133MB/s per channel. PCI Bus 32bit PCI Bus Master for 133MB/s of data transfer rate Supports Scatter / Gather function Automatic FIFO threshold selection Low command overhead True PCI Plug and Play. OS Compatibility. Mac OS X Mac OS 8.5 OS 9 and higher |
|
|
SATA to IDE Converter - Storage controller - IDE - SATA $24.99 Black Box SATA to IDE Converter - Storage controller - IDE - SATA |
|
|
SYBA SATA III + IDE ports (2+1) PCI-Express RAID Controller Card $75.86 1X SYBA SATA III + IDE ports (2+1) PCI-Express RAID Controller Card [OEM] SD-PEX40035Expand your computers connectivity with this combo set with PCI SATA III + IDE ports controller cardBased on Marvel 88SE9128 PCI-express 2.0 SATA 6Gbps hardware RAID controller1-lane PCI-express 2 interface supports communication speed of 2.5Gbps and 5.0GbpsCompliant with PCI-express 2.0 base specificationUnique hard drive activity LED indicator circuit designLED blinks when there is read / write activity on any one of the hard drives connected to the motherboard SATA port or to the add-on cardSerial-ATA (SATA) interface:Two SATA 6.0Gbps portsCompliant with Serial-ATA (SATA) specification 3.0Supports communication speeds of SATA III 6.0Gbps, SATA II 2.0Gbps, and SATA I 1.5Gbps hard drives and SSDSupports Gen 1i, Gen 1x, Gen 2i, Gen 2m, Gen 2x & Gen 3iSupports hardware RAID 0 and RAID 1Supports native command queuing (NCQ)Supports SATA port multiplier FIS based switching or command based switchingSupports SATA port hot-plugSupports AHCI 1.0 and IDE programming interfaceSupports ATA and ATAPI commandsParallel-ATA (PATA / IDE) interface:One PATA port supporting 2 ATA / ATAPI / IDE devices (master and slave)Compliant with ATA / ATAPI-7 specificationSupports DMA protocols, and up to UDMA 150Mbps data transfer rateSupports multiword DMA and PIO modes for data transferSupports IDE programming interfaceIncludes:SATA III and IDE combo ports (2+1) PCI-e RAID cardDriver CDUser manualLED cable: 11 inchDimensions: 6.5 x 5 x 1.5 inchBrand: SYBAModel: SD-PEX40035UPC: 810154017706 |
|
|
Lenovo RAID Controller 45J9047 $133.4 Lenovo RAID Controller 45J9047 |
|
|
Intel RAID Controller RS25AB080 $1870.99 RAID Controller RS25AB080 |
|
|
Intel RAID Controller RS25SB008 $2049.78 RAID Controller RS25AB080 |
|
|
ACARD AEC6880 PCI Ultra ATA 133 RAID IDE Adapter $68.45 AEC6880 is a high performance dualchannel PCI PP Ultra ATA133 RAID adapter. It supports true Hardware RAID 0 1 0+1 and JBOD. The easeofuse RAID utility helps quickly create and mange RAID subsystem. The 48bit LBA (Logical Block Addressing) technology makes it good for big hard drive over 137GB. AEC6880 fully supports 32bit PCI specifications including Bus Master to increase transfer capability and also supports Scatter/Gather function to enhance multitasking effects.RAID function. Supports true Hardware RAID 0 1 and 0+1 (under Windows) Capable Booting from standard and RAID volume (under Windows). Features. A standalone PCITOIDE controller Supports RAID 0 1 0+1 and JBOD (under Windows) Support Ultra ATA 133/100/66/33 HDD Supports big capacity hard disks (>=137GB) Cost effective and high performance. IDE BUS. Dual independent IDE channels Supports Ultra DMA 06 modes MultiWord DMA and PIO data transfer. Uses 48bit LBA technology to support high capacity hard drives. PCI BUS. Conforms to PCI 2.2 specifications Data transfer rate up to 133 MB/sec Supports Scatter / Gather function Low command overhead Supports multitasking and multithreaded processing PCI Plug and Play. Specifications. IDE processor:ATP865 Data I/O Mode:32bit PCI Bus Master Data transfer rate up to 133 MB/s Supports big HDD (>=137GB) Connects up to 4 devices Supports two IDE 40pin connectors Provides firmware update Coexists with onboard IDE controller. O.S Compatibility. Windows Server 2003 Windows XP Windows 2000 Professional Server Advanced Server Windows NT4.0 Workstation Server Windows 98 / ME Linux RedHat after 7.3(Software RAID Only) |
|
|
Koutech IO-PIR133 PCI IDE Controller Card $18.99 Internal Connectors: 2 x ATA 133 RAID: RAID 0/1/0+1 Operating Systems Supported: Windows 95/98/98SE/Me/NT 4.0/2000/XP, and DOS Features: 32-bit 33/66MHz PCI interface; 256 Byte FIFO per ATA channel; Large FIFO independent; Supports Ultra DMA 6/5/4/3/2/1, PIO 4/3/2/1/0, DMA 2/1/0 modes; IDE drive types support ATA, Fast ATA-2, EIDE, Ultra ATA/33, Ultra ATA/66, Ultra ATA/100, and Ultra ATA/133 Package Contents: IO-PIR133 Driver Disk IDE/PATA Cable |
|
|
ACARD AEC6897 PCI Ultra 4 Channels IDE RAID Adapter $110.57 ACARD AEC6897 series is a 4channel IDE RAID controller. The series includes AEC6897LP (low profile edition) which can support the standard 1U server. AEC6897 is compatible with PCIX interface on the motherboard for server. Its 4 independent channels can connect up to 8 hard drives. Through the 48bit LBA technology it can support a big hard drive of 137GB too. Its RAID levels have 0 1 0+1 5 JBOD and normal modes. It can provide storage strength to workstations and computers in the server class. Besides if it is used together with ACARD ACS4600 Tray it will support hot swap and rebuild data automatically. The Windowsbased RAID Utility is a GUI tool easy for you to manage the RAID subsystem. Thus the maintenance of server will be more convenient. AEC6897 fully supports the 64bit PCI specification including the instruction set of Bus Master to enhance the transfer performance. In addition it supports the Scatter/Gather function to increase the multitasking of OS. With its high transfer rate and good capability AEC6897 is exactly fit for workstation and server in the PC field. It can satisfy your needs in data storage and protection.Features. Supports RAID 0 1 0+1 5 and JBOD Supports hot swap and rebuilds data automatically (used with ACS4600)only one drive per channel Useful Windowsbased RAID Utility Notifies the abnormality of a hard drive by email Supports the spare function Supports the connection of the 2nd AEC6897. Suitability. Digital monitoring system Workstation File server and mail server Mainframe backup system Digital audio video editing system Database. Specifications. Data I/O mode: 64bit/66MHz PCI Bus Master Transfer rate up to 533 MB/s Supports a big hard drive (> 137GB) Connects up to 8 IDE hard drives(two drives per channel) Supports four internal 40pin IDE connectors Onboard flash BIOS for firmware update Coexists with the IDE controlling chip on the motherboard IDE BUS. Has 4 independent IDE channels. Supports Ultra DMA 133 mode (th |
|
|
StarTech 2S1I PCI SATA IDE Combo Controller Adapter Card $30.99 Type: PCI to SATA / IDE Card Internal Ports: 2 x SATA 1 x IDE Data Transfer Rate: Serial ATA Data Transfer Rate: Up to 150MBps IDE Data Transfer Rate: Up to 133MBps Operating Systems Supported: Windows 98/98SE/ME/NT 4.0/2000/XP/Vista Features: Compliant with PCI specification revision 2.2, and SATA 1.0 specification revision 1.0 Connect two SATA drives on independent channels and up to two IDE devices on a single channel.V2.2 One internal IDE port with data transfer up to 133 MBytes/sec SATA data transfer rates of up to 150Mbps Supports RAID 0, RAID 1, and JBOD Ultra ATA-133 / IDE data transfer rate up to 133Mbps Package Contents: PCISAT2IDE1 User Manual Driver Disk SATA Cable IDE Cable Parts: 1 year limited Labor: 1 year limited |
|
|
Addonics ADSA2 Serial ATA RAID Controller $31.99 0 1 1 Year 2 2 x 7-pin SATA - Serial ATA 2.48" Height x 4.92" Width x 0.74" Thickness Built-in RAID 0 and RAID 1 support Can be configured to operate as a non-RAID or RAID controller Support large hard drives of 137 GB or greater Integrated PCI DMA engines Independent 256-byte FIFOs (32 bit*64 deep) per Serial ATA channel for host reads and writes Upgradeable firmware Fits standard Desktop case and low profile systems Hot swap device can be removed and added without system shut down or restart PC/AT or Compatible System Pentium or greater Minimum 32 MB RAM 10 MB minimum free hard disk space One free PCI slot Plug and Play Compatible with ATA33/66/100/133 hard drives and ATATPI devices using the optional Addonics IDE to Serial ATA converter Work with any Serial ATA drive Serial ATA PCI host controller with standard height bracket and 1 low profile bracket Software CD User Guide Looking to get more speed out of your hard drive, hot swap capability and better air flow in the over crowded interior of your desktop computer? Addonics Serial ATA line of product is your answer. The Addonics Serial ATA PCI host controller is the most cost effective solution for adding Serial ATA capability to your Desktop computer. Coupling with Addonics IDE-Serial ATA converter, adding serial ATA to any desktop computer is easy and affordable. ADSA2 ADSA2 Serial ATA RAID Controller Addonics Addonics Technologies PCI Plug-in Card SATA RAID Controller Up to 150 MBps www.addonics.com |
|
|
SYBA SY-PEX50039 PCI Express SATA / IDE Controller Card $19.99 The SYBA PCIe SATA/IDE controller card provides 2 internal SATA II Ports and 1 Internal IDE (PATA) Port, allowing you to extend your PC’s storage internally. The PCIe x1 interface has a 2.5Gb/s full-duplex transfer rate to handle the multiple transfers. Thanks to the flexibility of PCIe x1, you can use the card in any available PCIe slot. Internal Connectors: 2 x SATA II + 1 x IDE Transfer Rate: Up to 3Gb/s RAID: RAID 0,1,0+1 JBOD Operating Systems Supported: Windows 7, Vista, Windows XP, Windows ME, Windows 98/98SE, Windwos NT, Windows 2000, Windows 2003 Features: JMB363 chipset (JMicron Technology Corporation) Supports 1-Lane 2.5Gbps PCI Express Bus Ports: (Internal Native Interface Multiplexed) 2 Internal SATA II Ports 1 Internal IDE (PATA) Port Compliant with Serial ATA AHCI (Advanced Host Controller Interface) Spec. Reversion 1.0 Compliant with Bus Master Programming Interface for IDE ATA Controllers Revision 1.0 Compliant with PCI Express Bas Spec. Revision 1.0a Compliant with Serial ATA High Speed Serialized AT Attachment Spec. Revision 1.0a Compliant with Serial ATA II: Extensions to Serial ATA 1.0a Revision 1.1 Compliant with Gen... |
|
|
HighPoint Rocket storage controller (RAID) $121.99 HighPoint Rocket - Storage controller (RAID) |
|
|
Intel / RAID Controller RS2BL080 / RS25GB008 $380.1 Intel - RAID Controller RS2BL080 - RS25GB008 |
|
|
Intel / RAID Controller RS2VB080 / RS2VB080 $790.8 Intel - RAID Controller RS2VB080 - RS2VB080 |