Amd Heatsink Fan

Computer Cooling

Causes of heat build up

The amount of heat generated by an integrated circuit (e.g., a CPU or GPU), the prime cause of heat build up in modern computers, is a function of the efficiency of its design, the technology used in its construction and the frequency and voltage at which it operates.

The dust on the laptop CPU heat sink after three years of use has made the laptop unusable due to frequent thermal shutdowns.

In operation, the temperature levels of a computer's components will rise until the temperature gradient between the computer parts and their surroundings is such that the rate at which heat is lost to the surroundings is equal to the rate at which heat is being produced by the electronic component, and thus the temperature of the component reaches equilibrium.

For reliable operation, the equilibrium temperature must be sufficiently low for the structure of the computer's circuits to survive.

Additionally, the normal operation of cooling methods can be hindered by other causes, such as:

Dust acting as a thermal insulator and impeding airflow, thereby reducing heat sink and fan performance.

Poor airflow including turbulence due to friction against impeding components, or improper orientation of fans, can reduce the amount of air flowing through a case and even create localised whirlpools of hot air in the case.

Poor heat transfer due to a lack or poor application of thermal compounds.

Damage prevention

It is common practice to include thermal sensors in the design of certain computer parts, e.g. CPUs and GPUs, along with internal logic that shuts down the computer if reasonable bounds are exceeded. It is, however, unwise to rely on such preventative measures, as it is not universally implemented, and may not prevent repeated incidents from permanently damaging the integrated circuit.

The design of an integrated circuit may also incorporate features to shut down parts of the circuit when it is idling, or to scale back the clock speed under low workloads or high temperatures, with the goal of reducing both power use and heat generation.

System cooling

Fan from Papst for racks.

Air cooling

Further information: Computer fan

While any method used to move air around or to computer enclosures would count as air cooling, fans are by far the most commonly used implement for accomplishing that task. The term computer fan usually refers to fans attached to computer enclosures, but may also be intended to signify any other computer fan, such as a CPU fan, GPU fan, a chipset fan, PSU fan, HDD fan, or PCI slot fans. Common fan sizes include 40, 60, 80, 92, 120, and 140 mm. Recently, 200mm fans have begun to creep into the performance market, as well as even larger sizes such as 230 and 240mm.

In desktops

Typical airflow through a desktop ATX case.

Desktop computers typically use one or more fans for heat management. Almost all desktop power supplies have at least one fan to exhaust air from the case. Most manufacturers recommend bringing cool, fresh air in at the bottom front of the case, and exhausting warm air from the top rear.

If there is more air being forced into the system than being pumped out (due to an imbalance in the number of fans), this is referred to as a "positive" airflow, as the pressure inside the unit would be higher than outside. A balanced or neutral airflow is the most efficient[citation needed], although a slightly positive airflow results in less dust build up if dust filters are used. Negative pressure inside the case can create problems such as clogged optical drives due to sucking in air (and dust).

In high density computing

Data centers typically contain many racks of flat 1U servers. Air is drawn in at the front of the rack and exhausted at the rear. Because data centers typically contain such large numbers of computers and other power-consuming devices, they risk overheating of the various components if no additional measures are taken. Thus, extensive HVAC systems are used. Often a raised floor is used so the area under the floor may be used as a large plenum for cooled air and power cabling.

Another way of accommodating large numbers of systems in a small space are blade chassis. In contrast to the horizontal orientation of flat servers, blade chassis are often oriented vertically. This vertical orientation facilitates convection. When the air is heated by the hot components, it tends to flow to the top on its own, creating a natural air flow along the boards. This stack effect can help to achieve the desired air flow and cooling. Some manufacturers expressly take advantage of this effect.

In laptop computing

Most laptops use air cooling in order to keep the CPU and other components within their operating temperature range. Because the air is fan forced through a small port, it can clog the fan and heatsinks with dust or be obstructed by objects placed near the port. This can cause overheating, and can be a cause of component failure in laptops. The severity of this problem varies with laptop design, its use and power dissipation. With recent reductions in CPU power dissipation, this problem can be anticipated to reduce in severity.

Liquid submersion cooling

An uncommon practice is to submerse the computer's components in a thermally conductive liquid. Personal computers that are cooled in this manner do not generally require any fans or pumps, and may be cooled exclusively by passive heat exchange between the computer's parts, the cooling fluid and the ambient air. Extreme density computers such as the Cray-2 may use additional radiators in order to facilitate heat exchange.

The liquid used must have sufficiently low electrical conductivity in order for it not to interfere with the normal operation of the computer's components. If the liquid is somewhat electrically conductive, it may be necessary to insulate certain parts of components susceptible to electromagnetic interference, such as the CPU. For these reasons, it is preferred that the liquid be dielectric.

Liquids commonly used in this manner include various liquids invented and manufactured for this purpose by 3M, such as Fluorinert. Various oils, including but not limited to cooking, motor and silicone oils have all been successfully used for cooling personal computers.

Evaporation can pose a problem, and the liquid may require either to be regularly refilled or sealed inside the computer's enclosure. Liquid may also slowly seep into and damage components, particularly capacitors, causing an initially functional computer to fail after hours or days immersed.

Waste heat reduction

Where full-power, full-featured modern computers are not required, some companies opt to use less powerful computers or computers with fewer features. For example: in an office setting, the IT department may choose a thin client or a diskless workstation thus cutting out the heat-laden components such as hard drives and optical disks. These devices are also often powered with direct current from an external power supply brick which still wastes heat, but not inside the computer itself.

The components used can greatly affect the power consumption and hence waste heat. A VIA EPIA motherboard with CPU typically generates approximately 25 watts of heat whereas a Pentium 4 motherboard typically generates around 140 watts. While the former has considerably less computing power, both types are adequate and responsive for tasks such as word processing and spreadsheets. Choosing a LCD monitor rather than a CRT can also reduce power consumption and excess room heat, as well as the added benefit of increasing available physical desk space.

Conductive and radiative cooling

Some laptop components, such as hard drives and optical drives, are commonly cooled by having them make contact with the computer's frame, increasing the surface area which can radiate and otherwise exchange heat.

Spot cooling

In addition to system cooling, various individual components usually have their own cooling systems in place. Components which are individually cooled include, but are not limited to, the CPU, GPU and the Northbridge chip. Some cooling solutions employ one or more methods of cooling, and may also utilize logic and/or temperature sensors in order to vary the power used in active cooling components.

Passive heat sink cooling

Passive heatsink fitted on a Intel GMA graphics chip

Passive heat sink cooling involves attaching a block of machined or extruded metal to the part that needs cooling. A thermal adhesive may be used, or more commonly for a personal computer CPU, a clamp is used to affix the heat sink right over the chip, with a thermal grease or pad spread between. This block usually has fins and ridges to increase its surface area. The heat conductivity of metal is much better than that of air, and its ability to radiate heat is better than that of the component part it is protecting (usually an integrated circuit or CPU). Until recently, fan cooled aluminium heat sinks were the norm for desktop computers. Today many heat sinks feature copper base-plates or are entirely made of copper, and mount fans of considerable size and power.

Heat sinks tend to get less effective with time due to the build up of dust between their metal fins, which reduces the efficiency with which the heat sink transfers heat to the ambient air. Dust build up can be countered with a gas duster by blowing away the dust along with any other unwanted excess material.

Passive heat sinks are commonly found on older CPUs, parts that do not get very hot (such as the chipset), and low-power computers.

Usually a heatsink is attached to the integrated heat spreader (IHS). It essentially is a large flat plate attached to the CPU (with conduction paste layered between). The plate is used to dissipate or spread the heat locally. Unlike a heatsink, its intent is to redistribute heat and not to remove it. In addition, the IHS offers protection to the fragile CPU.

Passive cooling avoids the generation of fan noise.

Active heat sink cooling

Active heatsink with a 120mm fan located inside the unit and attached fan controller in background

Active heat sink cooling uses the same principle as passive, with the addition of a fan that is directed to blow over or through the heat sink. The moving air increases the rate at which the heat sink can exchange heat with the ambient air. Active heat sinks are the primary method of cooling a modern processor or graphics card.

The buildup of dust is greatly increased with active heat sink cooling as the fan is continually taking in the dust present in the surrounding air. As a result, dust removal procedures need to be exercised much more frequently than with passive heat sink methods.

Peltier cooling or thermoelectric cooling

Main article: Thermoelectric cooling

In 1821 T. J. Seebeck discovered that different metals, connected at two different junctions, will develop a micro-voltage if the two junctions are held at different temperatures. This effect is known as the "Seebeck effect"; it is the basic theory behind the TEC (thermoelectric cooling).

In 1834 Jean Peltier discovered the inverse of the Seebeck effect, now known as the "Peltier effect". He found that applying a voltage to a thermocouple creates a temperature differential between two sides. This results in an effective, albeit extremely inefficient heat pump.

Modern TECs use several stacked units each composed of dozens or hundreds of thermocouples laid out next to each other, which allows for a substantial amount of heat transfer. A combination of bismuth and telluride is most commonly used for thermocouples.

Since TECs are active heat pumps, they are capable of cooling PC components below ambient temperatures, which is impossible with common radiator cooled water cooling systems and heatpipe HSFs.

Water cooling

Main article: Water cooling

While originally limited to mainframe computers, water cooling has become a practice largely associated with overclocking in the form of either manufactured kits, or in the form of do-it-yourself setups assembled from individually gathered parts. The past few years has seen water cooling increasing its popularity with pre-assembled, moderate to high performance, desktop computers. Water has the ability to dissipate more heat from the cooled parts than the various types of metals used in heatsinks, making it suitable for overclocking and high performance computer applications. Advantages to water cooling include the fact that a system is not limited to cooling one component, but can be set up to cool the central processing unit, graphics processing unit, and/or other components at the same time with the same system. As opposed to air cooling, water cooling is also influenced less by the ambient temperature. Water cooling's comparatively low noise-level is also favorable to that of active cooling, which can become quite noisy. One disadvantage to water cooling is the potential for a coolant leak. Leaked coolant can damage any electronic components it comes in contact with. Another drawback to water cooling is the complexity of the system; an active heat sink is much simpler to build, install, and maintain than a water cooling solution.

DIY Water cooling setup showing 12v pump, CPU Waterblock and the typical application of a T-Line

DIY Water cooling setup showing 12v MCP655 Vario pump, Swiftech GTZ CPU Waterblock and the non-typical use of a Reservoir.

Heat pipe

Main article: Heat pipe

A graphics card with a heatpipe cooler design.

A heat pipe is a hollow tube containing a heat transfer liquid. As the liquid evaporates, it carries heat to the cool end, where it condenses and then returns to the hot end (under capillary action, or, in earlier implementations, under gravitation). Heat pipes thus have a much higher effective thermal conductivity than solid materials. For use in computers, the heat sink on the CPU is attached to a larger radiator heat sink. Both heat sinks are hollow as is the attachment between them, creating one large heat pipe that transfers heat from the CPU to the radiator, which is then cooled using some conventional method. This method is expensive and usually used when space is tight (as in small form-factor PCs and laptops), or absolute quiet is needed (such as in computers used in audio production studios during live recording). Because of the efficiency of this method of cooling, many desktop CPU's and GPU's, as well as high end chipsets, use heat pipes in addition to active fan-based cooling to remain within safe operating temperatures.

Phase-change cooling

Phase-change cooling is an extremely effective way to cool the processor. A vapor compression phase-change cooler is a unit which usually sits underneath the PC, with a tube leading to the processor. Inside the unit is a compressor of the same type as in a window air conditioner. The compressor compresses a gas (or mixture of gases) which condenses it into a liquid. Then, the liquid is pumped up to the processor, where it passes through an expansion device, this can be from a simple capillary tube to a more elaborate thermal expansion valve. The liquid evaporates (changing phase), absorbing the heat from the processor as it draws extra energy from its environment to accommodate this change (see latent heat). The evaporation can produce temperatures reaching around 15 to -150  degrees Celsius. The gas flows down to the compressor and the cycle begins over again. This way, the processor can be cooled to temperatures ranging from 15 to 150  degrees Celsius, depending on the load, wattage of the processor, the refrigeration system (see refrigeration) and the gas mixture used. This type of system suffers from a number of issues but mainly one must be concerned with dew point and the proper insulation of all sub-ambient surfaces that must be done (the pipes will sweat, dripping water on sensitive electronics).

Alternately a new breed of cooling system is being developed inserting a pump into the thermo siphon loop. This adds another degree of flexibility for the design engineer as the heat can now be effectively transported away from the heat source and either reclaimed or dissipated to ambient. Junction temperature can be tuned by adjusting the system pressure; higher pressure equals higher fluid saturation temperatures. This allows for smaller condensers, smaller fans and/or the effective dissipation of heat in a high ambient environment. These systems are in essence the next generation liquid cooling paradigm as they are approximately 10 times more efficient than single phase water. Since the system uses a dielectric as the heat transport media, leaks do not cause a catastrophic failure of the electric system.

This type of cooling is seen as a more extreme way to cool components, since the units are relatively expensive compared to the average desktop. They also generate a significant amount of noise, since they are essentially refrigerators, however the compressor choice and air cooling system is the main determinant of this, allowing for flexibility for noise reduction based on the parts chosen.

Liquid nitrogen

Liquid nitrogen may be used to cool an overclocked PC.

As liquid nitrogen evaporates at -196 C, far below the freezing point of water, it is valuable as an extreme coolant for short overclocking sessions.

In a typical installation of liquid nitrogen cooling, a copper or aluminum pipe is mounted on top of the processor or graphics card. After being heavily insulated against condensation, the liquid nitrogen is poured into the pipe, resulting in temperatures well below -100C.

By welding an open pipe onto a heat sink, and insulating the pipe, it is possible to cool the processor either with liquid nitrogen, which has a temperature below 196C, or dry ice. However, after the nitrogen evaporates, it has to be refilled. In the realm of personal computers, this method of cooling is seldom used in contexts other than overclocking trial-runs and record-setting attempts, as the CPU will usually expire within a relatively short period of time due to temperature stress caused by changes in internal temperature.

Liquid helium

Liquid helium, colder than liquid nitrogen, has also been used for cooling. Liquid helium evaporates at -269 C, and temperatures ranging from -230 to -240 C have been measured from the heatsink.

Soft cooling

Softcooling is the practice of utilizing software to take advantage of CPU power saving technologies to minimize energy use. This is done using halt instructions to turn off or put in standby state CPU subparts that aren't being used or by underclocking the CPU.

Undervolting

Undervolting is a practice of running the CPU or any other component with voltages below the device specifications. An undervolted component draws less power and thus produces less heat. The ability to do this varies by manufacturer, product line, and even different production runs of the same exact product (as well as that of other components in the system), but modern processors are typically shipped with voltages higher than strictly necessary. This provides a buffer zone so that the processor will have a higher chance of performing correctly under sub-optimal conditions, such as a lower quality mainboard (motherboard). However, too low a voltage will not allow the processor to function correctly, producing errors, system freezes or crashes, or the inability to turn the system on. (Undervolting too far does not typically lead to hardware damage, though in worst-case scenarios, program or system files can be corrupted)

This technique is generally employed by those seeking low-noise systems, as less cooling is needed because of the reduction of heat production.

Integrated chip cooling techniques

Conventional cooling techniques all attach their ooling component to the outside of the computer chip, or via IHS and/or heat sinks. This ttaching technique will always exhibit some thermal resistance, reducing its effectiveness. The heat can be more efficiently and quickly be removed by directly cooling the local hot spots. At these locations, power dissipation of over 300W/cm2 (typical CPU are less than 100W/cm2, although future systems are expected to exceed 1000W/cm2 ) can occur. This form of local cooling is essential to developing high power density chips. This ideology has led to the investigation of integrating cooling elements into the computer chip. Currently there are two techniques: micro-channel heat sinks, and jet impingement cooling.

In micro-channel heat sinks, channels are fabricated into the silicon chip (CPU), and coolant is pumped through them. The channels are designed with very large surface area which results in large heat transfers. Heat dissipation of 3000W/cm2 has been reported with this technique . In comparison to the Sun power density of around 7400W/cm2. The heat dissipation can be further increased if two-phase flow cooling is applied. Unfortunately the system requires large pressure drops, due to the small channels, and the heat flux is lower with dielectric coolants used in electronic cooling. Another local chip cooling technique is jet impingement cooling. In this technique, a coolant is flown through a small orifice to form a jet. The jet is directed toward the surface of the CPU chip, and can effectively remove large heat fluxes. Heat dissipation of over 1000W/cm2has been reported . The system can be operated at lower pressure in comparison to the micro-channel method. The heat transfer can be further increased using two-phase flow cooling and by intergrading return flow channels (hybrid between micro-channel heat sinks and jet impingement cooling).

Cooling and overclocking

Extra cooling is usually required by those who run parts of their computer (such as the CPU and GPU) at higher voltages and frequencies than manufacturer specifications call for, called overclocking. Increasing performance by this modification of settings results in a greater amount of heat generated and thus increasing the risk of damage to components and/or premature failure.

The installation of higher performance, non-stock cooling may also be considered modding. Many overclockers simply buy more efficient, and often, more expensive fan and heat sink combinations, while others resort to more exotic ways of computer cooling, such as liquid cooling, Peltier effect heatpumps, heat pipe or phase change cooling.

There are also some related practices that have a positive impact in reducing system temperatures:

Heat sink lapping

Heat sink lapping is the smoothing and polishing of the contact (bottom) part of a heat sink to increase its heat transfer efficiency. The desired result is a contact area which has a more even surface, as a less even contact surface creates a larger amount of insulating air between the heat sink and the computer part it is attached to. Polishing the surface using a combination of fine sandpaper and abrasive polishing liquids can produce a mirror-like shine, an indicator of a very smooth metal surface. However, it should be noted that even a curved surface can become extremely reflective, yet not particularly flat, as is the case with curved mirrors; thus heat sink quality is based on overall flatness, more than optical properties. Lapping a high quality heat sink can damage it, because, although the heat sink may become shiny, it is likely that more material will be removed from the edges, making the heat sink less effective overall.

If attempted, a piece of float glass should be used, as it self-levels as it cools and offers the most economical solution to producing a perfectly flat surface.

Use of exotic thermal conductive compounds

Some overclockers use special thermal compounds whose manufacturers claim to have a much higher efficiency than stock thermal pads. Heat sinks clean of any grease or other thermal transfer compounds have a very thin layer of these products applied, and then are placed normally over the CPU. Many of these compounds have a high proportion of silver as their main ingredient due to its high thermal conductivity. The resulting difference in the temperature of the CPU is measurable (several degrees celsius), so the heat transfer does appear to be superior to stock compounds. Some people experience negligible gains and have called to question the advantages of these exotic compounds, calling the style of application more important than the compound itself. Also note that there may be a 'setting' or 'curing' period and negligible gains may improve over time as the compound reaches its optimum thermal conductivity.

Use of rounded cables

Most older PCs use flat ribbon cables to connect storage drives (IDE or SCSI). These large flat cables greatly impede airflow by causing drag and turbulence. Overclockers and modders often replace these with rounded cables, with the conductive wires bunched together tightly to reduce surface area. Theoretically, the parallel strands of conductors in a ribbon cable serve to reduce crosstalk (signal carrying conductors inducing signals in nearby conductors), but there is no empirical evidence of rounding cables reducing performance. This may be because the length of the cable is short enough so that the effect of crosstalk is negligible. Problems usually arise when the cable is not electromagnetically protected and the length is considerable, a more frequent occurrence with older network cables.

These computer cables can then be cable tied to the chassis or other cables to further increase airflow.

This is less of a problem with new computers that use Serial ATA which has a much narrower cable.

Airflow optimization

The colder the cooling medium (the air), the more effective the cooling. Cooling air temperature can be reduced by these guidelines:

Supply cool air to the hot components as directly as possible. Examples are air snorkels and tunnels that feed outside air directly and exclusively to the CPU or GPU cooler. For example, the BTX case design prescribes a CPU air tunnel.

Expel warm air as directly as possible. Examples are: Conventional PC (ATX) power supplies blow the warm air out the back of the case. Many dual-slot graphics card designs blow the warm air through the cover of the adjacent slot. There are also some aftermarket coolers that do this. Some CPU cooling designs blow the warm air directly towards the back of the case, where it can be ejected by a case fan.

Air that has already been used to spot-cool a component should not be reused to spot-cool a different component (this follows from the previous items). The ATX case design can be said to violate this rule, since the power supply gets its "cool" air from the inside of the case, where it has been warmed up already. The BTX case design also violates this rule, since it uses the CPU cooler's exhaust to cool the chipset and often the graphics card.

Prefer cool intake air, avoid inhaling exhaust air (outside air above or near the exhausts). For example, a CPU cooling air duct at the back of a tower case would inhale warm air from a graphics card exhaust. Moving all exhausts to one side of the case, conventionally the back, helps to keep the intake air cool.

Hiding cables behind motherboard tray or simply apply ziptie and tucking cables away to provide unhindered airflow.

Fewer fans strategically placed will improve the airflow internally within the PC and thus lower the overall internal case temperature in relation to ambient conditions. The use of larger fans also improves efficiency and lowers the amount of waste heat along with the amount of noise generated by the fans while in operation.

There is little agreement on the effectiveness of different fan placement configurations, and little in the way of systematic testing has been done. For a rectangular PC (ATX) case, a fan in the front with a fan in the rear and one in the top has been found to be a suitable configuration. However, AMD's (somewhat outdated) system cooling guidelines notes that "A front cooling fan does not seem to be essential. In fact, in some extreme situations, testing showed these fans to be recirculating hot air rather than introducing cool air." It may be that fans in the side panels could have a similar detrimental effect -- possibly through disrupting the normal air flow through the case. However, this is unconfirmed and probably varies with the configuration.

See also

Thermal management of electronic devices and systems

Full immersion cooling

References

^ Verari Systems uses vertical air flow for cooling

^ The tower case Silverstone Raven RV01 has been designed to make use of the stack effect

^ Tom's Hardware - "Strip Out The Fans", 9 January 2006, presented as 11 web pages.

^ oilcooledcomputer.com

^ AMD Phenom II Overclocked to 6.5GHz - New World Record for 3DMark

^ I. Mudawar, ssessment of High-Heat-Flux Thermal Management Schemes, IEEE Trans. -Components and Packaging Tech., Vol. 24, pp. 122-141, 2001.

^ M.B. Bowers and I. Mudawar, igh Flux Boiling inLow Flow Rate, Low Pressure Drop Mini-Channel and Micro-Channel Heat Sinks, Int. J. Heat Mass Transfer, Vol. 37, pp. 321-332, 1994.

^ M.K. Sung and I. Mudawar, ingle-phase and two-phase hybrid cooling schemes for high-heat-flux thermal management of defense electronics, Thermal and Thermomechanical Phenomena in Electronic Systems, 2008. ITHERM 2008,Issue 28-31, pp.121 131, 2008.

^ AMD Athlon System Cooling Guidelines -- Although somewhat out of date, it appears to be backed up by some amount of systematic testing -- which is lacking in many other guides.

External links

Wikibooks has a book on the topic of

How To Assemble A Desktop PC/Silencing#Liquid nitrogen cooling

Online Heat Sink Performance Calculators

CPU Cooler Rules of Thumb

Submersion Cooling Patent Application

Categories: Computer hardware cooling | Central processing unitHidden categories: All articles with unsourced statements | Articles with unsourced statements from April 2007
About the Author

I am China Toys Suppliers writer, reports some information about embossing leather , wholesale yarn.

StarTech.com UNIVERSAL AMD 64-BIT CPU HEATSINK W/ FAN FANK8AM2 $16.46 StarTech.com UNIVERSAL AMD 64-BIT CPU HEATSINK W/ FAN FANK8AM2

Startech Universal AMD 64-bit CPU Heatsink with Fan $26.99 This AMD CPU Cooler Fan supports Athlon 64 X2 dual core (Socket AM2) and older AMD K8 CPUs, offering the perfect way to ensure optimum system performance._x000D_ Featuring a 92mm ever-lubricate ball-bearing fan, the AMD CPU cooler also offers an aluminum heatsink that helps dissipate and remove the harmful heat that comes as a result of typical drive operation._x000D_ A cost-effective solution that helps to increase CPU lifespan by optimizing the processors operating environment, the AMD CPU cooler can be powered through a simple TX3 (3-pin) connection to the computer power supply._x000D_ View AMD Compatibility Chart Manufacturer: StarTech.com Manufacturer Part Number: FANK8AM2 Manufacturer Website Address: www.startech.com Brand Name: StarTech.com Product Name: 92x25mm AMD Ball Bearing CPU Cooler Fan Product Type: Cooling Fan/Heatsink Fan Information: Fan Bearing Type: Ball Bearing Heatsink Information: Cooler Type: Thermoelectric Interfaces/Ports: Connectors: 3-pin TX3 Female Compatibility: AMD - Socket AM2 dual core processor Athlon 64 X2 5000, 5600+ AMD - K8 family processors Athlon 64 4000+, Athlon 64 FX-57, Opteron 854, Sempron 3600+ Application/Usage: Processor

Supermicro Active Heatsink for AMD (Socket F) CPU $31.99 1 1 x 5400 rpm 13.58 oz 4-pin LP4 4.13" x 4" x 3.07" - Heatsink 5400 rpm AMD - Up to Two Dual-Core Opteron 2000 Series Socket F, Opteron Socket 940 Dual 1207-pin Socket F Active Heatsink for AMD (Socket F) CPU Cooling Fan/Heatsink Processor SNK-P0024AP4 Side Fan Straight Fin Supermicro Supermicro Computer, Inc www.supermicro.com

CPU Replacement Cooling Fan Cooler Heat Sink Heatsink for AMD 775 $15.49 Description:This CPU Fan Cooler works excellent in heat dissipation and extends the life and functionality of your computer.It can keep your processor cool with optimal temperature and improve air flow for your CPU.Unique heatsink sheet design, the premium AMD 775 Heatsink works with double efficiency than ordinary fan.CPU Fan Cooler is a must in protecting your valuable data by keeping your CPU coolLow Noise Cooling Master CPU Fan Cooler for AMD has the advantages of Highspeed fan running with low noise levelThis CPU Cooler protects your valuable data efficently by keeping your CPU cool.Fitness: for AMD 755Measurement: 11cm in diameter, 4.8cm in heightWeight: 301g

60x65mm Socket A CPU Cooler Fan with Heatsink for AMD Duron or Athlon - processor cooler $9.99 StarTech.com 60x65mm Socket A CPU Cooler Fan with Heatsink for AMD Duron or Athlon - Processor cooler - ( Socket A ) - 60 mm

Dynatron / Dynatron CPU Cooler T71G AMD Opteron Socket 940 Heatsink+Fan 1U Copper / T71G $32.51 Dynatron - Dynatron CPU Cooler T71G AMD Opteron Socket 940 Heatsink+Fan 1U Copper - T71G

StarTech.com 1U Low Profile Socket AM2 AMD Heatsink with Fan - 70mm - 4000rpm - 1 x Ball Bearing FANK8AM21U $43.1 StarTech.com 1U Low Profile Socket AM2 AMD Heatsink with Fan - 70mm - 4000rpm - 1 x Ball Bearing FANK8AM21U

StarTech.com 1U Low Profile Socket AM2 AMD Heatsink with Fan $33.99 1 1 Year 1 x 25.6 CFM 1 x 4000 rpm - ± 10% 1 x 70 mm 1 x Ball Bearing 1" Height x 2.83" Width x 4.21" - Product 1.16 lb 12 V 1U Low Profile Socket AM2 AMD Heatsink with Fan 2.76" x 2.76" x 0.39" - Fan 3-pin TX3 Female 32 4.21" x 2.83" x 1" - Heatsink 4000 rpm 70 mm CPU Supported: Socket AM2 - Athlon X2 BE, Athlon 64 X2, Athlon 64 LE Socket 754/939 - Athlon 64 Socket AM2 - Opteron 1210-1218HE Socket AM2 - Sempron All copper heatsink & Skive Fin technology Designed to direct hot air away from your CPU Combines suitable design with effective heat dispersion This 1U Low Profile TX3 AMD CPU Cooler Fan features a built-on heatsink which helps maximize CPU heat dissipation, while its 7cm fan directs hot air away from your CPU - helping to maintain ideal operating conditions for your hard working AMD processor. Offering air flow up to 25.63 CFM, the cooler fan features a high quality dual ball bearing design, that not only ensures reliability but also helps extend the fan/cooler life span. Cooling Fan/Heatsink FANK8AM21U Processor RoHS Side Fan StarTech.com Straight Fin Thermoelectric Yes www.startech.com

Thermaltake CLS0015 Cooling Fan/Heatsink $33.99 0.39" Height x 2.76" Width x 2.76" Depth - Fan 1 1 x 30.5 CFM 1 x 4800 rpm - ± 10% 1 x 70 mm 1 x Ball Bearing 1 x Sleeve Bearing 1" Height x 2.95" Width x 4.55" Depth - Heatsink 14.72 oz 3 Year Limited 3-pin 4800 rpm 70 mm AMD Socket: G34 AMD Opteron 6000 Series (Multi-Cores) Processor CLS0015 CLS0015 Cooling Fan/Heatsink Cooling Fan/Heatsink Processor RoHS Spring Screw Thermaltake Thermaltake Technology Co., Ltd Yes www.thermaltakeusa.com

Thermaltake CLS0017 Cooling Fan/Heatsink $39.99 0.59" Height x 2.76" Width x 2.76" Depth - Fan 1 1 x 47 CFM 1 x 6000 rpm 1 x 70 mm 1 x Ball Bearing 1 x Sleeve Bearing 1.12 lb 2.10" Height x 3.18" Width x 4.53" Depth - Heatsink 3 Year Limited 4-pin 6000 rpm 70 mm AMD Socket: G34 AMD Opteron 6000 Series (Multi-Cores) Processor CLS0017 CLS0017 Cooling Fan/Heatsink Cooling Fan/Heatsink Processor RoHS Spring Screw Thermaltake Thermaltake Technology Co., Ltd Yes www.thermaltakeusa.com

Zalman CNPS8000A Cooling Fan/Heatsink $39.99 1 1 Year Limited Parts & Labor 1 x 2800 rpm 1 x 92 mm 1 x Dual Ball Bearing 11.64 oz 12 V DC 2.60" Height x 4.25" Width x 4.25" Length 2800 rpm 3-pin TX3 92 mm CNPS8000A Cooling Fan/Heatsink Backplate Side Caps Nuts Loading Block Double-sided Tape Thermal Grease (ZM-STG2M) FAN MATE 2 FAN MATE 2 Cable Double-sided Tape User's Manual Intel Clip (For Intel Socket 1366/1156/775) AMD Clip (For AMD Socket AM3/AM2+/AM2) Intel Socket: LGA1156 LGA1366 LGA775 AMD Socket: AM3 AM2+ AM2 Intel Processor: Core i7 Extreme Core i7 Core i5 Core i3 Core 2 Quad Core 2 Duo Core 2 Extreme Pentium Dual Core Pentium D Pentium 4 Celeron D AMD Processor: Phenom II Athlon II Dual-Core Opteron Phenom Athlon FX Athlon X2 Athlon Sempron CNPS8000A CNPS8000A Cooling Fan/Heatsink Cooling Fan/Heatsink Processor Zalman Zalman Tech Co., LTD www.zalmanusa.com

Corsair A50 Cooling Fan/Heatsink $44.99 1 1 x 120 mm 1 x 2000 rpm 1 x 61 CFM 120 mm 2 Year Limited 2000 rpm 4.72" Height x 4.72" Width x 0.98" Depth - Fan 6.28" Height x 4.91" Width x 3.20" Depth - Heatsink Air A50 Cooling Fan/Heatsink Multi-platform Mounting Kit Thermal Compound Quick Start Guide Intel Sockets: LGA 775 LGA 1366 LGA 1156 AMD Sockets: Core AM2 Core AM3 The superior engineering of the Air Series A50 makes it dramatically outperform your CPU's stock heatsink: three 8mm copper heatpipes directly contact your CPU and instantly pull heat up into the aluminum cooling fins. A 120mm fan, mounted on rubber studs to reduce noise and vibration, quietly draws cool air through the fins. A50 Air Air A50 Cooling Fan/Heatsink CAFA50 Cooling Fan/Heatsink Corsair Corsair Memory Processor www.corsairmicro.com

6cm Heatsink and Fan CPU Computer Cooler $24.97 An entrylevel heatsink specifically designed for AMD Athlon and Duron processors. This heatsink with fan provides enough cooling power for most Athlon and Duron CPUs without costing a fortune. Suitable for Duron CPUs up to 1300 MHz Thunderbird Athlon CPUs up to 1333 MHz and Athlon XP CPUs up to 2000+.

Universalhsf - Startech.Com Universal Intel P4 Amd Athlon Cpu Cooler Fan With Heatsink - 3500Rpm $23.1 building A System? Don't Waste Time Trying To Match Component Compatibilities. Startech.com's Univeralhsf Is A Heavy Duty Heatsink And Fan That Fits Most Intel And Amd Processors! the Extra-large Aluminum Heatsink And 7x7 Cm Ball Bearing Fan Cools The Most Powerful Processors, And Fits The Following: Intel Piii And P4 Up To 3.2 Ghz, Amd Athlon Xp 3000+, And Amd K7 & K8. Comes Complete With Intel And Amd Clips And Thermal Transfer Compound For Quick, Professional Quality Installation. And It Comes With An Eye-catching Purple Heatsink And Uv Reactive Fan! [1108018] UPC: 065030808736 UNSPC: 43201538 6.4L x 3.4W x 4.8H 0.9 LB 0.03 Cubes

Zalman CNPS10XPERFORMA Cooling Fan/Heatsink $45.99 1 1 x 120 mm 1 x 1350 rpm 1.65 lb 120 mm 1350 rpm 225259 4-pin LP4 6" x 3.94" x 5.20" CNPS10XPERFORMA Cooling Fan/Heatsink Backplate Resistor[RC24P] Side Caps Bolts Nuts Fan Fixing Clips Vibration Pads Loading Block Thermal Grease(ZM-STG2) Double-Sided Tape User's Manual Intel Clip(For Intel Socket 1156/1366/775) AMD Clip(For AMD Socket AM3/AM2+/AM2) AMD Clip(For AMD Socket 754/939/940) Intel CPU: Core i7 Core i5 Core i3 Core i7 Core 2 Quad Core 2 Duo Core 2 Extreme Pentium Dual Core Pentium D Pentium 4 Celeron D AMD CPU: Phenom II Athlon II Phenom II Phenom Athlon FX Athlon X2 Athlon Sempron Athlon Dual-Core Opteron Opteron Intel Socket: LGA1156 1366 775 AMD Socket: AM3 AM2+ AM2 754 939 940 Optimally designed aluminum fins disperse heat away from the CPU via 5 heatpipes, while switching noise free, high capacity 120mm fan quickly cools the heatsink for stable operation of high performance CPUs. CNPS10XPERFORMA CNPS10XPERFORMA Cooling Fan/Heatsink Cooling Fan/Heatsink Processor Zalman Zalman Tech Co., LTD www.zalmanusa.com

Corsair A70 Cooling Fan/Heatsink $52.99 120 mm 2 2 Year Limited 2 x 120 mm 2 x 2000 rpm 2 x 61 CFM 2000 rpm 4.72" Height x 4.72" Width x 0.98" Depth - Fan 6.28" Height x 4.91" Width x 5.08" Depth - Heatsink Air A70 Cooling Fan/Heatsink Multi-platform Mounting Kit Thermal Compound Quick Start Guide Intel Sockets: LGA 775 LGA 1366 LGA 1156 AMD Sockets: Core AM2 Core AM3 The Corsair Cooling A70 High-Performance CPU Cooler uses advanced thermal engineering technology to deliver superior air cooling performance: four 8mm copper heatpipes directly contact your CPU, and the surface is planed to increase heat transfer efficiency. Dual speed-selectable 120mm fans, mounted on rubber studs, spin quietly in a push-pull configuration for optimum airflow. A70 Air Air A70 Cooling Fan/Heatsink CAFA70 Cooling Fan/Heatsink Corsair Corsair Memory Processor www.corsairmicro.com

Fandurontb - Startech.Com 60X65Mm Socket A Cpu Cooler Fan With Heatsink For Amd Duron Or Athlon - 60Mm - 4000Rpm $10.5 an Entry-level Heatsink Specifically Designed For Amd Athlon And Duron Processors. This Heatsink With Fan Provides Enough Cooling Power For Most Athlon And Duron Cpus Without Costing A Fortune. Suitable For Duron Cpus Up To 1300 Mhz, Thunderbird Athlon Cpus Up To 1333 Mhz And Athlon Xp Cpus Up To 2000+. [495728] UPC: 065030787314 UNSPC: 43201538 3.2L x 3.6W x 2.5H 0.5 LB 0.03 Cubes

Thermaltake CL-P0554 Cooling Fan/Heatsink $56.99 0.24" Heatpipe 1 1 x 1600 rpm 1 x 80 mm 1.09 lb 1600 rpm 3-pin TX3 3.15" x 3.15" x 3.35" - Fan 4.73" x 6.26" - Heatsink 80 mm Intel Socket LGA 1366 Processor: Core i7 Intel Socket LGA 1156 Processor: Core i7 Core i5 Core i3 Intel Socket LGA 775 Processor: Core 2 Extreme Core 2 Quad Core 2 Duo Pentium D Pentium 4 Pentium Celeron D Celeron AMD Socket AM3 Processor: Phenom II x4 Phenom II x3 AMD Socket AM2 / AM2+ / 939 / 754 Processor: Phenom Athlon 64 FX Athlon 64 X2 Athlon 64 Sempron CL-P0554 Cooling Fan/Heatsink Fan with Red LED Processor Retail Side Fan SpinQ VT CPU Cooler Thermaltake Thermaltake Technology Co., Ltd www.thermaltakeusa.com

Zalman CNPS9900MAX-R Cooling Fan/Heatsink $128.87 Manufacturer: Zalman Tech Co., LTD Manufacturer Part Number: CNPS9900MAX-R Manufacturer Website Address: www.zalmanusa.com Brand Name: Zalman Product Series: CNPS9900 Product Model: CNPS9900MAX-R Product Name: CNPS9900MAX-R Cooling Fan/Heatsink Product Type: Cooling Fan/Heatsink Fan Information: Fan Bearing Type: Long Life Bearing Heatsink Information: Mount Type: Clip Mount Interfaces/Ports: Connectors: 4-pin Package Contents: CNPS9900MAX-R Cooling Fan/Heatsink Backplate Users Manual Thermal Grease Resistor Wrench Gold Bolts Silver Bolts Nut(Slide) Caps Gold Nuts (9900 LED/NT) Silver Nuts (9900 MAX) Loading Block Double-sided Tape Intel Clip AMD Clip Compatibility: Intel Socket 1155/1156/1366/775 CPU: Core i7 Extreme Core i7 Core i5 Core i3 Core 2 Extreme Core 2 Quad Core 2 Duo Dual Core Pentium Pentium D Pentium 4 Celeron D AMD Socket AM3/AM2+/AM2 CPU: Phenom II Phenom Athlon II Athlon X2 Athlon FX Athlon Opteron Dual-Core Opteron Sempron Application/Usage: Processor

Zalman CNPS7000B-Cu LED Processor Heatsink and Cooling Fan $41.99 0.71 oz - Fan Mate 2 1 Year Limited 1.02" Height x 1.02" Width x 2.76" Length - FAN MATE 2 1.66 lb - CNPS7000B-Cu LED 2.44" Height x 4.29" Width x 4.29" Length - CNPS7000B-Cu LED 2600 rpm 2600 rpm - ± 10% 3-pin TX3 92 mm CNPS7000B-Cu LED Processor Heatsink and Cooling Fan Four Bolts Thermal Grease Fan Speed Controller (FAN MATE 2) Double-sided Tape (for installing FAN MATE 2) Cable for FAN MATE 2 User Manual - in English and Korean Components for Intel Pentium 4 (Socket 478): Two Clip Supports Components for AMD Duron/Athlon/Athlon XP/Sempron (Socket 462): One A-Type (Blue) Clip Support One B-Type (White) Clip Support Four Bolts - For fastening the Clip Supports One set of Washers Components for AMD Sempron/AMD64 (Socket 754/939/940): Two Nipples One Backplate Small washers CNPS7000B-Cu LED Processor Heatsink and Cooling Fan does not generate noise or vibration in Silent Mode Pure Copper base material ensures excellent heat dissipation 92mm fan inside the FHS maximizes airflow and makes installation easier Adjustable fan speed controller (FAN MATE 2) enables control of noise and fan performance LED Color: Blue Noise Level: 18.0 ~ 27.5 dB ± 10% Intel Socket 478: Celeron Celeron D Pentium 4: Willamette Northwood Prescott AMD Socket 462: Duron Sempron Athlon: Thunderbird Palomino Athlon XP: Thoroughbred Barton AMD Socket 754: Sempron Athlon 64 AMD Socket 939: Athlon 64 Athlon 64 FX AMD Socket 940: Athlon 64 FX Opteron CNPS7000B-Cu LED CNPS7000B-Cu LED Processor Heatsink and Cooling Fan Cooling Fan/Heatsink Copper Heatsink Dual Ball Bearing Processor Thermoelectric Zalman Zalman Tech Co., LTD www.zalmanusa.com

Zalman CNPS9700 NT Processor Heatsink and Cooling fan $56.99 1.68 lb 110 mm 2800 rpm 5.59" Height x 4.88" Width x 3.54" Length - FHS Automatic Fan Speed Control feature included in the Ultra Quiet 110mm PWM(Pulse Width Modulation) enabled fan 100% copper heatsink with aerodynamically optimized tunnel design for maximum cooling efficiency Innovative, patented, figure 8 heatpipe design for a heat transfer capacity of up to six heatpipes with the use of just three 0.2mm ultra-slim fins for minimized weight and reduced airflow resistance Super Thermal Grease (ZM-STG1) included Intel Socket 775 Processors: Celeron D Pentium 4 Pentium D Core 2 Duo AMD Socket AM2: Sempron Athlon 64 Athlon 64 X2 Athlon 64 FX AMD Socket 754: Sempron Athlon 64 AMD Socket 939: Athlon 64 Athlon 64 X2 Athlon 64 FX Opteron Dual-Core Opteron AMD Socket 940: Athlon 64 FX Opteron Dual-Core Opteron Noise Level: Silent Mode: 19.5dB ± 10% Normal Mode: 35dB ± 10% Aluminum/Copper Heatsink CNPS9700 NT Processor Heatsink and Cooling fan CNPS9700NT Cooling Fan/Heatsink Dual Ball Bearing Processor Thermoelectric Zalman Zalman Tech Co., LTD www.zalmanusa.com

Zalman CNPS9500 AM2 Processor Cooling Fan & Heatsink $46.99 0.71 oz - Fan Mate 2 1 Year Limited 1.02" Height x 1.02" Width x 2.76" Length - FAN MATE 2 1.17 lb - Heatsink 2600 rpm 2600 rpm - ± 10% 3-pin TX3 4.92" Height x 4.41" Width x 3.35" Length - Heatsink CNPS9500 AM2 Processor Cooling Fan & Heatsink 1 x Clip 1 x Lever Thermal Grease FAN MATE 2 (Fan Speed Controller) Cable for FAN MATE2 Double-sided Tape(to attach FAN MATE2) User Manual Pure copper heatsink with component layout optimized for maximum cooling efficiency Innovative, patented, and curved heatpipe design for a heat transfer capacity of up to six heatpipes with the use of just three Ultra slim fins (0.2mm) for minimized weight and reduced airflow resistance AMD Socket AM2: Sempron Processors Athlon 64 Processors Athlon 64 X2 Processors Athlon 64 FX Processors AMD Socket 754: Sempron Processors Athlon 64 Processors AMD Socket 939: Athlon 64 Processors Athlon 64 X2 Processors Athlon 64 FX Processors Opteron Processors Dual-Core Opteron Processors AMD Socket 940: Opteron Processors Athlon 64 FX Processors Dual-Core Opteron Processors Noise Level: Silent Mode: 18.0dB ± 10% Low-noise Mode: 27.5dB ± 10% CNPS9500 AM2 CNPS9500 AM2 Processor Cooling Fan & Heatsink Cooling Fan/Heatsink Copper Heatsink Dual Ball Bearing Processor Thermoelectric Zalman Zalman Tech Co., LTD www.zalmanusa.com

Cooler Master RR-H101-22FK-RA Cooling Fan/Heatsink $20.99 1 1 x 2200 rpm 1 x 30 CFM 1 x 80 mm 1 x Sleeve Bearing 10.72 oz 2200 rpm 3-pin TX3 3.15" Height x 3.15" Width x 0.98" Depth - Fan 3.29" x 2.68" x 4.61" - Heatsink 80 mm AMD Socket AM3 / AM2 / 940 / 939: Athlon II X2 Athlon Sempron Cooler Master Cooler Master Co., Ltd Cooling Fan/Heatsink Processor ROHS RR-H101-22FK-RA RR-H101-22FK-RA Hyper 101A CPU Cooler Retail Side Fan Yes www.coolermaster-usa.com

Zalman CNPS9900 NT Cooling Fan/Heatsink $62.99 1 1 Year 1 x 120 mm 1 x 2000 rpm 1 x Ball Bearing 1.61 lb 120 mm 2000 rpm 4-pin LP4 6" Height x 5.16" Width x 3.62" Length CNPS9900 NT Cooling Fan/Heatsink ZM-STG2 Thermal Grease RC33P Resistor Cable Washers User Manual Socket 1156/775 Clip Socket 1156/775 Clip Support Socket 775 Backplate Socket 1156 Nuts Socket 1156/775 Bolts (Silver) Socket 1366 Clip Socket 1366 Clip Support Socket 1366 Bolts (Gold) AMD Clip AMD Clip Lever Intel CPU: Core i7 Core i5 Core i3 Core i7 Core 2 Quad Core 2 Duo Core 2 Extreme Pentium Dual Core Pentium D Pentium 4 Celeron D AMD CPU: Phenom II Athlon II Phenom Athlon FX Athlon X2 Athlon Sempron Dual-Core Opteron Opteron Intel Socket: LGA1156 LGA1366 LGA775 AMD Socket: AM3 AM2+ AM2 754 939 940 CNPS9900 CNPS9900 NT CNPS9900 NT Cooling Fan/Heatsink Cooling Fan/Heatsink Processor Retail Zalman Zalman Tech Co., LTD www.zalmanusa.com

Corsair Hydro CWCH70 Cooling Fan/Heatsink $102.99 1.76 lb 120 mm 2 2 Year Limited 2 x 120 mm 2 x 2000 rpm 2 x 61.2 CFM 2000 rpm 4.72" x 4.72" x 0.98" - Fan Hydro CWCH70 Cooling Fan/Heatsink Mounting Brackets Step-down Adapters Socket: LGA775 LGA1366 LGA775 1156 AM2 AM3 A low profile pump and improved cold plate allow for even easier mounting to your CPU. Compatibility with all modern AMD and Intel desktop CPU sockets is included in the box. A higher-performance radiator with nearly twice the surface provides even more room for liquid to get cool before it returns to the cold plate. CWCH70 Cooling Fan/Heatsink Corsair Corsair Memory Hydro Hydro CWCH70 Cooling Fan/Heatsink Processor Pushpin www.corsairmicro.com

StarTech FANDURONTB 60mm Ball Socket A CPU Cooler Fan with Heatsink for AMD Duron or Athlon $14.99 Type: Fan & Heatsinks RPM: 4000 RPM Air Flow: 23 CFM Noise Level: 38 dBA Power Connector: 3 Pin Color: Black Heatsink Material: Aluminum Compatibility: Socket A

Cooler Master DK9-7E52A-0L-GP Cooling Fan/Heatsink $14.99 1 1 x 3200 rpm 1.61" Height x 3.03" Width x 2.68" Length 12 V DC 3-pin TX3 30 3200 rpm 6 Year AMD Socket: AM3 AM2 AMD Socket: Sempron All Series Athlon X2 All Series (up to 65W) Athlon II X2 All Series (up to 65W) Athlon II X3 All Series (up to 65W) Athlon II X4 All Series (up to 65W) Phenom II X3 (up to 65W) Phenom II X4 (up to 65W) Clip Mount Cooler Master Cooler Master Co., Ltd Cooling Fan/Heatsink DK9-7E52A-0L-GP DK9-7E52A-0L-GP Cooling Fan/Heatsink PC Processor www.coolermaster-usa.com

Zalman CNPS9700 LED Processor Heatsink and Cooling Fan $53.99 0.71 oz - Fan Mate 2 1 Year Limited 1.02" Height x 1.02" Width x 2.76" Length - FAN MATE 2 1.52 lb - FHS 110 mm 2800 rpm 2800 rpm - ± 10% 3-pin TX3 5.59" Height x 4.88" Width x 3.54" Length - FHS Does not generate noise or vibration in Silent Mode Adjustable fan speed controller (FAN MATE 2) included 0.2mm ultra-slim fins for minimized weight and reduced airflow resistance 100% copper heatsink with aerodynamically optimized tunnel design for maximum cooling efficiency Innovative and patented, curved heatpipe design for a heat transfer capacity of up to six heatpipes with the use of just three CNPS9700 LED Processor Heatsink and Cooling Fan 1 x Thermal Grease (ZM-STG1) 1 x Fan Speed Controller (FAN MATE 2) 1 x FAN MATE 2 Cable 1 x Double-sided Tape (For attaching FAN MATE 2) 1 x User Manual Components for Intel Socket 775: 1 x Backplate 1 x Clip (S-Type) 1 x Clip Support 4 x Bolts (for installing the cooler) 4 x Clip Support Fixing Bolts Components for AMD Sockets AM2/754/939/940: 1 x Clip 1 x Clip Lever Intel Scoket 775: Celeron D Processor Pentium 4 Processor Pentium D Processor Core 2 Duo Processor AMD Socket AM2: Sempron Processor Athlon 64 Processor Athlon 64 X2 Processor Athlon 64 FX Processor AMD Socket 754: Sempron Processor Athlon 64 Processor AMD Socket 939: Opteron Processor Athlon 64 Processor Athlon 64 X2 Processor Athlon 64 FX Processor Dual-Core Opteron Processor AMD Socket 940: Opteron Processor Athlon 64 FX Processor Dual-Core Opteron Processor Noise Level: Silent Mode: 19.5dB ± 10% Normal Mode: 35dB ± 10% 03 Heat Pipes CNPS9700 LED Processor Heatsink and Cooling Fan CNPS9700LED Cooling Fan/Heatsink Copper Heatsink Dual Ball Bearing Processor Thermoelectric Zalman Zalman Tech Co., LTD www.zalmanusa.com

Lenovo S10-2 Fan And Heatsink 31037866 $25.1 Lenovo S10-2 Fan And Heatsink 31037866

Dell PE1600SC HEATSINK/FAN 7R181 $29.66 Dell PE1600SC HEATSINK/FAN 7R181

HP CPU Heatsink/Fan 3ICT8TATP08 $34.4 HP CPU Heatsink/Fan 3ICT8TATP08

HP CPU Heatsink/Fan KFB04505HA $34.4 HP CPU Heatsink/Fan KFB04505HA

HP CPU Heatsink/Fan 394298001 $34.4 HP CPU Heatsink/Fan 394298001

HP Heatsink/Fan Kit 418485001 $34.4 HP Heatsink/Fan Kit 418485001

This entry was posted on Wednesday, July 19th, 2006 at 8:23 pm and is filed under Uncategorized. You can follow any responses to this entry through the RSS 2.0 feed. You can leave a response, or trackback from your own site.